If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C1374 - 18

    Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation

    Active Standard ASTM C1374 | Developed by Subcommittee: C16.32

    Book of Standards Volume: 04.06

      Format Pages Price  
    PDF 5 $54.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $54.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $64.00   ADD TO CART

    Significance and Use

    5.1 This test method was designed to give the manufacturer of loose-fill insulation products a way of determining what the initial installed thickness should be in a horizontal open attic for pneumatic applications.

    5.2 The installed thickness value developed by this test method is intended to provide guidance to the installer in order to achieve a minimum mass/unit area for a given R-value.

    5.3 For the purpose of product design, testing should be done at a variety of R-values. At least three R-values should be used: the lowest R-value on the product label, the highest R-value on the product label, and an R-value near the midpoint of the R-value range.

    Note 1: For quality control purposes, testing may be done at one R-value of R-19 (h×ft 2×°F/Btu) or higher.

    5.4 Specimens are blown in a manner consistent with the intended installation procedure. Blowing machine settings should be representative of those typically used for field application with that machine.

    5.5 The material blown for a given R-value as part of the installed thickness test equals the installed mass/unit area times the test chamber area. This mass can be calculated from information provided on the package label at the R-value prescribed.

    1. Scope

    1.1 This test method covers determination of the installed thickness of pneumatically applied loose-fill building insulations prior to settling by simulating an open attic with horizontal blown applications.

    1.2 This test method is a laboratory procedure for use by manufacturers of loose-fill insulation for product design, label development, and quality control testing. The apparatus used produces installed thickness results at a given mass/unit area.

    1.3 This test method is not the same as the design density procedures described in Test Methods C520 or Specifications C739 or C764.

    1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C168 Terminology Relating to Thermal Insulation

    C520 Test Methods for Density of Granular Loose Fill Insulations

    C739 Specification for Cellulosic Fiber Loose-Fill Thermal Insulation

    C764 Specification for Mineral Fiber Loose-Fill Thermal Insulation

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    ICS Code

    ICS Number Code 91.100.60 (Thermal and sound insulating materials); 91.120.10 (Thermal insulation of buildings)

    UNSPSC Code

    UNSPSC Code 30141500(Thermal insulation)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1374-18

    Citation Format

    ASTM C1374-18, Standard Test Method for Determination of Installed Thickness of Pneumatically Applied Loose-Fill Building Insulation, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top