If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C1330 - 18

    Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants

    Active Standard ASTM C1330 | Developed by Subcommittee: C24.10

    Book of Standards Volume: 04.07

      Format Pages Price  
    PDF 2 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 2 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 4 $56.00   ADD TO CART


    This standard specification covers the basic requirements for cylindrical sealant backing for use with cold liquid-applied sealants. Cylindrical sealant backings are classified into three types: type C, type O, and type B, composed predominantly of closed cell material, open cell material, and bi-cellular material, respectively. Test methods for cylindrical sealant backing include water absorption, density, outgassing, compression deflection and recovery, and tensile strength. The sealant shall be clean, free of scale, foreign matter, oil, or water.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    Significance and Use

    5.1 This specification is designed to give some indication as to the differences in performance for various cylindrical sealant backings.

    5.2 Although this specification qualifies a cylindrical sealant backing for use, it does not address the compatibility of the backing with the sealants with which it will make contact. Sealant compatibility should be confirmed by the sealant manufacturer. Compatibility characteristics of sealants in contact with cylindrical sealant backings can be determined by Test Method C1087.

    1. Scope

    1.1 This specification covers the basic requirements for cylindrical sealant backing to be used with cold liquid applied sealants for use in building seals.

    1.2 Cylindrical sealant backing serves one or more of the following functions:

    1.2.1 Limits the amount and depth of sealant applied into a joint,

    1.2.2 Acts as a bond breaker to allow joint movement without undue stress to the sealant,

    1.2.3 Provides a form to assist the sealant in developing the proper shape factor, and

    1.2.4 Acts as a barrier to the flow of sealant through the joint.

    1.3 The committee with jurisdiction over this standard is not aware of any comparable standards published by other ASTM committees or other organizations.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C717 Terminology of Building Seals and Sealants

    C1016 Test Method for Determination of Water Absorption of Sealant Backing (Joint Filler) Material

    C1087 Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems

    C1253 Test Method for Determining the Outgassing Potential of Sealant Backing

    D1622 Test Method for Apparent Density of Rigid Cellular Plastics

    D1623 Test Method for Tensile and Tensile Adhesion Properties of Rigid Cellular Plastics

    D5249 Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints

    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 31200000(Adhesives and sealants)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1330-18

    Citation Format

    ASTM C1330-18, Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top