If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C127 - 15

    Método de prueba estándar para la densidad relativa (gravedad específica) y la absorción del agregado grueso

    Active Standard ASTM C127 Developed by Subcommittee: C09.20

    Book of Standards Volume: 04.02


      Format Pages Price  
    PDF 8 $200.00   ADD TO CART

    Historical Version(s) - view previous versions of standard

    Translated Standard(s): English

    ASTM License Agreement

    More C09.20 Standards Related Products


    Significance and Use

    5.1 Relative density (specific gravity) is the ratio of mass of an aggregate to the mass of a volume of water equal to the volume of the aggregate particles – also referred to as the absolute volume of the aggregate. It is also expressed as the ratio of the density of the aggregate particles to the density of water. Distinction is made between the density of aggregate particles and the bulk density of aggregates as determined by Test Method C29/C29M, which includes the volume of voids between the particles of aggregates.

    5.2 Relative density is used to calculate the volume occupied by the aggregate in various mixtures containing aggregate, including hydraulic cement concrete, bituminous concrete, and other mixtures that are proportioned or analyzed on an absolute volume basis. Relative density (specific gravity) is also used in the computation of voids in aggregate in Test Method C29/C29M. Relative density (specific gravity) (SSD) is used if the aggregate is in a saturated-surface-dry condition, that is, if its absorption has been satisfied. Alternatively, the relative density (specific gravity) (OD) is used for computations when the aggregate is dry or assumed to be dry.

    5.3 Apparent relative density (specific gravity) pertain to the solid material making up the constituent particles not including the pore space within the particles that is accessible to water.

    5.4 Absorption values are used to calculate the change in the mass of an aggregate due to water absorbed in the pore spaces within the constituent particles, compared to the dry condition, when it is deemed that the aggregate has been in contact with water long enough to satisfy most of the absorption potential. The laboratory standard for absorption is that obtained after submerging dry aggregate for a prescribed period of time. Aggregates mined from below the water table commonly have a moisture content greater than the absorption determined by this test method, if used without opportunity to dry prior to use. Conversely, some aggregates that have not been continuously maintained in a moist condition until used are likely to contain an amount of absorbed moisture less than the 24-h soaked condition. For an aggregate that has been in contact with water and that has free moisture on the particle surfaces, the percentage of free moisture is determined by deducting the absorption from the total moisture content determined by Test Method C566.

    5.5 The general procedures described in this test method are suitable for determining the absorption of aggregates that have had conditioning other than the 24-h soak, such as boiling water or vacuum saturation. The values obtained for absorption by other test methods will be different than the values obtained by the prescribed soaking, as will the relative density (specific gravity) (SSD).

    1. Alcance

    1.1 Este método de prueba abarca la determinación de la densidad relativa (gravedad específica) y la absorción de los agregados gruesos. La densidad relativa (gravedad específica), una cantidad adimensional, se expresa como la densidad de secado al horno (oven-dry, OD), saturado con superficie seca (saturated-surface-dry, SSD) o densidad relativa aparente (gravedad específica aparente). La densidad relativa OD se determina después del secado del agregado. La densidad relativa SSD y la absorción se determinan después de remojar el agregado en agua durante el tiempo indicado.

    1.2 Este método de prueba no está diseñado para ser utilizado con agregados ligeros que cumplen con los agregados del Grupo I de la Especificación C332.

    1.3 Los valores indicados en unidades del Sistema Internacional (SI) deben considerarse como estándar. No se incluyen otras unidades de medida en este estándar.

    1.4 El texto de este método de prueba hace referencia a notas y notas al pie, que proporcionan material explicativo. Esas notas y notas al pie (excluyendo las de las tablas y figuras) no se deberán considerar requisitos de este método de prueba.

    1.5 Este estándar no pretende abordar todas las inquietudes de seguridad, en caso de existir alguna, relacionadas con su uso. Es responsabilidad del usuario de este estándar establecer las prácticas de salud y seguridad apropiadas y determinar la aplicabilidad de las limitaciones normativas antes de su uso.

    2. Documentos Citados