If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C127 - 15

    Método de ensaio padrão para Densidade relativa (grau específico) e absorção de agregados graúdos

    Active Standard ASTM C127 Developed by Subcommittee: C09.20

    Book of Standards Volume: 04.02


      Format Pages Price  
    PDF 8 $200.00   ADD TO CART

    Historical Version(s) - view previous versions of standard

    Translated Standard(s): English

    ASTM License Agreement

    More C09.20 Standards Related Products


    Significance and Use

    5.1 Relative density (specific gravity) is the ratio of mass of an aggregate to the mass of a volume of water equal to the volume of the aggregate particles – also referred to as the absolute volume of the aggregate. It is also expressed as the ratio of the density of the aggregate particles to the density of water. Distinction is made between the density of aggregate particles and the bulk density of aggregates as determined by Test Method C29/C29M, which includes the volume of voids between the particles of aggregates.

    5.2 Relative density is used to calculate the volume occupied by the aggregate in various mixtures containing aggregate, including hydraulic cement concrete, bituminous concrete, and other mixtures that are proportioned or analyzed on an absolute volume basis. Relative density (specific gravity) is also used in the computation of voids in aggregate in Test Method C29/C29M. Relative density (specific gravity) (SSD) is used if the aggregate is in a saturated-surface-dry condition, that is, if its absorption has been satisfied. Alternatively, the relative density (specific gravity) (OD) is used for computations when the aggregate is dry or assumed to be dry.

    5.3 Apparent relative density (specific gravity) pertain to the solid material making up the constituent particles not including the pore space within the particles that is accessible to water.

    5.4 Absorption values are used to calculate the change in the mass of an aggregate due to water absorbed in the pore spaces within the constituent particles, compared to the dry condition, when it is deemed that the aggregate has been in contact with water long enough to satisfy most of the absorption potential. The laboratory standard for absorption is that obtained after submerging dry aggregate for a prescribed period of time. Aggregates mined from below the water table commonly have a moisture content greater than the absorption determined by this test method, if used without opportunity to dry prior to use. Conversely, some aggregates that have not been continuously maintained in a moist condition until used are likely to contain an amount of absorbed moisture less than the 24-h soaked condition. For an aggregate that has been in contact with water and that has free moisture on the particle surfaces, the percentage of free moisture is determined by deducting the absorption from the total moisture content determined by Test Method C566.

    5.5 The general procedures described in this test method are suitable for determining the absorption of aggregates that have had conditioning other than the 24-h soak, such as boiling water or vacuum saturation. The values obtained for absorption by other test methods will be different than the values obtained by the prescribed soaking, as will the relative density (specific gravity) (SSD).

    1.1 Este método de ensaio abrange a determinação da densidade relativa (grau específico) e da absorção de agregados graúdos. A densidade relativa (grau específico), uma quantidade adimensional, é expressa como densidade relativa de secagem em estufa (OD), saturada com superfície seca (SSD) ou densidade relativa aparente (grau específico aparente). A densidade relativa de OD é determinada após a secagem do agregado. A densidade relativa SSD e a absorção são determinadas após a imersão do agregado em água pela duração indicada.

    1.2 Este método de ensaio não se destina a ser usado com agregados leves em conformidade com a Especificação C332, agregados do grupo I.

    1.3 Os valores indicados no sistema internacional de unidades (SI) devem ser considerados como padrão. Nenhuma outra unidade de medida está incluída nesta norma.

    1.4 O texto deste método de ensaio se refere às observações e notas de rodapé que fornecem materiais explicativos. Essas observações e notas de rodapé (excluindo aquelas em tabelas e figuras) não devem ser consideradas requisitos deste método de ensaio.

    1.5 Esta norma não pretende abordar todas as preocupações de segurança, se houver, associadas à sua utilização. É responsabilidade do usuário desta norma estabelecer práticas apropriadas de saúde e segurança e determinar a aplicabilidade das limitações regulatórias antes do uso.