Products and Services / Standards & Publications / Standards Products


    If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM C1184 - 18e1

    Standard Specification for Structural Silicone Sealants

    Active Standard ASTM C1184 | Developed by Subcommittee: C24.10

    Book of Standards Volume: 04.07

      Format Pages Price  
    PDF 4 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $48.00   ADD TO CART

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center   Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Historical Version(s) - view previous versions of standard

    ASTM License Agreement

    Shipping & Handling

    More C24.10 Standards Related Products Standard References

    Abstract

    This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems. Sealants shall be classified as to types and uses: Type S; Type M; Use G; and Use O. The physical, mechanical, and performance properties of the sealant shall conform to the requirements described. The following test methods shall be performed: rheological properties; extrudability; hardness; heat aging; tack-free time; tensile adhesion; and shelf life.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification describes the properties of cold liquid applied, single-component or multicomponent, chemically curing elastomeric structural silicone sealants herein referred to as the sealant. These sealants are intended to structurally adhere components of structural sealant glazing systems.

    1.2 Only those properties for which there are industry-agreed-upon minimum acceptable requirements, as determined by available ASTM test methods, are described in this specification. Additional properties may be added as ASTM test methods for those properties become available.

    1.3 The values stated in metric (SI) units are to be regarded as the standard. The values in parentheses are for information only.

    1.4 Committee C24, with jurisdiction over this specification, is aware of two comparable standards by other organizations: ETAG No. 002 and the Chinese national standard GB16776.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C603 Test Method for Extrusion Rate and Application Life of Elastomeric Sealants

    C639 Test Method for Rheological (Flow) Properties of Elastomeric Sealants

    C661 Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer

    C679 Test Method for Tack-Free Time of Elastomeric Sealants

    C717 Terminology of Building Seals and Sealants

    C792 Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants

    C794 Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants

    C1087 Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems

    C1135 Test Method for Determining Tensile Adhesion Properties of Structural Sealants

    C1401 Guide for Structural Sealant Glazing

    C1442 Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus

    G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

    G154 Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials

    G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials

    European Organization for Technical Approvals Document

    ETAG No. 002

    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 31133710(Silicone sealant)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1184-18E01

    Citation Format

    ASTM C1184-18e1, Standard Specification for Structural Silicone Sealants, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top