| Format | Pages | Price |   |
![]() |
3 | $46.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 3 | $46.00 | ![]() |
Historical Version(s) - view previous versions of standard
More C09.46 Standards Related Products Standard References
Significance and Use
4.1 Specimens obtained in accordance with the procedure section of this practice may be used for preconstruction studies of shotcrete mixtures, to qualify nozzlemen and equipment, or for quality control, or compressive or flexural strength testing, during the progress of a project.
1. Scope
1.1 This practice covers procedures for preparing test panels of dry-mix or wet-mix shotcrete and for testing specimens sawed or cored from the panels.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 The text of this standard references notes and footnotes that provide explanatory materials (excluding those in tables and figures) that shall not be considered as requirements of the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C42/C42M Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
C78/C78M Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)
C125 Terminology Relating to Concrete and Concrete Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C171 Specification for Sheet Materials for Curing Concrete
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C457/C457M Test Method for Microscopical Determination of Parameters of the Air-Void System in Hardened Concrete
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes
C513/C513M Test Method for Obtaining and Testing Specimens of Hardened Lightweight Insulating Concrete for Compressive Strength
C642 Test Method for Density, Absorption, and Voids in Hardened Concrete
C995 Test Method for Time of Flow of Fiber-Reinforced Concrete Through Inverted Slump Cone
C1018 Test Method for Flexural Toughness and First-Crack Strength of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
C1399/C1399M Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete
ICS Code
ICS Number Code 91.100.30 (Concrete and concrete products)
UNSPSC Code
UNSPSC Code
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/C1140_C1140M-11R19
Citation Format
ASTM C1140 / C1140M-11(2019), Standard Practice for Preparing and Testing Specimens from Shotcrete Test Panels, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top