ASTM C1127 / C1127M - 15

    Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface

    Active Standard ASTM C1127 / C1127M | Developed by Subcommittee: D08.25

    Book of Standards Volume: 04.04

      Format Pages Price  
    PDF 13 $58.00   ADD TO CART
    Hardcopy (shipping and handling) 13 $58.00   ADD TO CART
    Standard + Redline PDF Bundle 26 $69.00   ADD TO CART

    Significance and Use

    4.1 This guide is divided into two sections which provide design and specification guidelines for the use of a cold liquid-applied elastomeric membrane with integral wearing surface for waterproofing building decks in building areas to be occupied by personnel, vehicles, or equipment.

    4.2 The intent of Sections 5 – 11, Design Considerations, is to provide information and design guidelines where a waterproofing membrane with integral wearing surface is to be used. The intent of the remaining sections is to provide minimum guide specifications for the use of the purchaser and the seller in contract documents.

    4.3 Where the state of the art is such that criteria for a particular condition is not as yet firmly established or has numerous variables that require consideration, reference is made to the applicable portion of Sections 5 – 11 that covers the particular area of concern. Section 16 describes the repair, rehabilitation, and replacement of the membrane.

    1. Scope

    1.1 This guide describes the design and installation of cold liquid-applied elastomeric waterproofing membrane systems that have an integral wearing surface. The cold liquid-applied elastomeric waterproofing membrane (membrane) to which this guide refers is specified in Specification C957.

    1.2 Concrete Slab-on-Grade—Waterproofing the upper surface of a concrete slab on grade presents special problems due to the possibility of negative hydrostatic pressure causing loss of bond to the substrate. Consideration of these problems is beyond the scope of this guide. Consult the membrane manufacturer for recommendations when this situation exists.

    1.3 The committee having jurisdiction for this guide is not aware of any similar ISO standard.

    1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements see 15.4.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C33 Specification for Concrete Aggregates

    C150 Specification for Portland Cement

    C330 Specification for Lightweight Aggregates for Structural Concrete

    C332 Specification for Lightweight Aggregates for Insulating Concrete

    C717 Terminology of Building Seals and Sealants

    C755 Practice for Selection of Water Vapor Retarders for Thermal Insulation

    C920 Specification for Elastomeric Joint Sealants

    C957 Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane With Integral Wearing Surface

    C962 Standards Guide for Use of Elastomeric Joint Sealants

    C1193 Guide for Use of Joint Sealants

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D1079 Terminology Relating to Roofing and Waterproofing

    D1752 Specification for Preformed Sponge Rubber Cork and Recycled PVC Expansion Joint Fillers for Concrete Paving and Structural Construction

    D2628 Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements

    U.S. Department of Commerce Standard

    Product Standard PS 1-74 Construction and Industrial Plywood Available from National Institute of Standards and Technology (NIST), 100 Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070,

    American Concrete Institute (ACI) Standard

    301-84 (1985) Specification for Structural Concrete for Buildings Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094,

    Steel Structures Painting Council (SSPC) Standards

    Specification SSPC SP-2 Wire Brush Cleaning Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor, Pittsburgh, PA 15222-4656,

    Specification SSPC SP-6 Commercial Blast Cleaning

    Steel Structures Painting Manual, Systems and Specifications:

    American Plywood Association (APA) Standard

    APA Plywood Construction Guide Available from American Plywood Assoc. (Forest Industries), P.O. Box 11700, Tacoma, WA 98411.

    ICS Code

    ICS Number Code 83.140.99 (Other rubber and plastic products)

    UNSPSC Code

    UNSPSC Code 30151505(Roofing membranes)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1127_C1127M-15

    Citation Format

    ASTM C1127 / C1127M-15, Standard Guide for Use of High Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with an Integral Wearing Surface, ASTM International, West Conshohocken, PA, 2015,

    Back to Top