| Format | Pages | Price |   |
![]() |
5 | $52.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 5 | $52.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
10 | $62.00 | ![]() |
Historical Version(s) - view previous versions of standard
More B05.02 Standards Related Products Standard References
Abstract
This specification covers the requirements for UNS C72900 copper-nickel-tin alloy rods and bars. Products should be manufactured by hot working, cold working, and annealing processes to produce a uniform wrought structure in the finished product. Each product should then be hot or cold worked to the finished size, and if required, should be subsequently annealed to meet the specified temper properties. The tensile strength and Rockwell hardness values from prescribed tests on the products should fall within the required range.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification establishes the requirements for copper-nickel-tin alloy rod and bar. The following alloy is included:
Copper Alloy | Nominal Composition, Weight % | ||
| Copper | Nickel | Tin |
C72900 | 77 | 15 | 8 |
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B601 Classification for Temper Designations for Copper and Copper AlloysWrought and Cast
B846 Terminology for Copper and Copper Alloys
E8/E8M Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E23 Test Methods for Notched Bar Impact Testing of Metallic Materials
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness
E478 Test Methods for Chemical Analysis of Copper Alloys
ICS Code
ICS Number Code 77.150.30 (Copper products)
UNSPSC Code
UNSPSC Code 30102409(Copper rods); 30262200(Copper bars)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0929-17
Citation Format
ASTM B929-17, Standard Specification for Copper-Nickel-Tin Spinodal Alloy Rod and Bar, ASTM International, West Conshohocken, PA, 2017, www.astm.org
Back to Top