If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM B927 / B927M - 17
Standard Specification for Brass Rod, Bar, and Shapes
| Format | Pages | Price | ||
 |
7 | $54.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 7 | $54.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
14 | $64.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More B05.02 Standards Related Products Standard References
Abstract
This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, and C27400. The material shall be made from cast billets, logs, or rods of copper alloy, as determined by chemical analysis. The products shall be manufactured by such hot working, cold working, and annealing processing as to produce a uniform wrought structure. The material shall conform to the chemical compositional requirements prescribed for copper, lead, iron, and zinc. The standard tempers, either hard or soft anneal (namely: O60, H01, H02, and H04), for rod and bar are specified. Tensile requirements to which the product shall conform includes tensile strength, yield strength, and elongation. The dimensional requirements for rods, bars, and shapes are given.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification establishes requirements for brass rod (round, hexagonal, and octagonal), bar (rectangular and square), and shapes of UNS Alloys C21000, C22000, C23000, C24000, C26000, C26800, C27000, C27400, C27450, C27451, C27453, and C28500.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B16/B16M Specification for Free-Cutting Brass Rod, Bar and Shapes for Use in Screw Machines
B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar
B121/B121M Specification for Leaded Brass Plate, Sheet, Strip, and Rolled Bar
B124/B124M Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
B134/B134M Specification for Brass Wire
B135 Specification for Seamless Brass Tube
B249/B249M Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
B587 Specification for Welded Brass Tube
E8/E8M Test Methods for Tension Testing of Metallic Materials
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E478 Test Methods for Chemical Analysis of Copper Alloys
ICS Code
ICS Number Code 77.150.30 (Copper products); 77.150.60 (Lead, zinc and tin products)
UNSPSC Code
UNSPSC Code 30102410(Brass rods); 30261500(Brass bars)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0927_B0927M-17
Citation Format
ASTM B927 / B927M-17, Standard Specification for Brass Rod, Bar, and Shapes, ASTM International, West Conshohocken, PA, 2017, www.astm.org
Back to Top