ASTM B775 / B775M - 16
Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
| Format | Pages | Price | ||
 |
6 | $46.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 6 | $46.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
12 | $55.20 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More B02.07 Standards Related Products Standard References
Abstract
This general specification contains the mandatory requirements to the ASTM standards listed herein for longitudinally welded piping made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2
| Title of Specification | ASTM |
|
| |
| Welded UNS N08020 Alloy Pipe | B464/B464M |
| Welded Nickel-Iron-Chromium Alloy Pipe | B514 |
| Welded Nickel-Chromium-Iron-Alloy (UNS N06600, | B517 |
| Welded Nickel and Nickel-Cobalt Alloy Pipe | B619/B619M |
| UNS N08904, UNS N08925, and UNS N08926 Welded Pipe | B673 |
| UNS N08367 Welded Pipe | B675 |
| Nickel-Alloy (UNS N06625, N06219, and N08825) Welded Pipe | B705 |
| Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe | B723 |
| Welded Nickel (UNS N02200/UNS N02201) and Nickel | B725 |
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy (UNS N06674) Plate, Sheet, and Strip
B464/B464M Specification for Welded UNS N08020 Alloy Pipe
B514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
B517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045) Pipe
B619/B619M Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B673 Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
B705 Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
B723 Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Pipe
B725 Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Pipe
B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys
B899 Terminology Relating to Non-ferrous Metals and Alloys
E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E39 Methods for Chemical Analysis of Nickel
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E112 Test Methods for Determining Average Grain Size
E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing
E426 Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E571 Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Products
E1473 Test Methods for Chemical Analysis of Nickel, Cobalt and High-Temperature Alloys
ANSI Standards
B1.20.1 Pipe Threads B36.19 Stainless Steel PipeSAE
SAE J 1086 Practice for Numbering Metals and Alloys (UNS)ICS Code
ICS Number Code 77.150.40 (Nickel and chromium products)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0775_B0775M-16
Citation Format
ASTM B775 / B775M-16, Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe, ASTM International, West Conshohocken, PA, 2016, www.astm.org
Back to Top