| Format | Pages | Price |   |
![]() |
6 | $50.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 6 | $50.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
12 | $60.00 | ![]() |
Historical Version(s) - view previous versions of standard
Work Item(s) - proposed revisions of this standard
More B05.01 Standards Related Products Standard References
Abstract
This standard covers the requirements for copper sheet, strip, plate, and rolled bar produced from copper with the following UNS Nos.; C10100, C10200, C10300, C10400, C10500, C10700, C10800, C10910, C11000, C11300, C11400, C11600, C12000, C12200, C12300, C14200, C14420, and C14530. Chemical composition shall conform to the chemical requirements pertaining to the materials UNS No. Tempering of materials shall be done by hot-rolling, cold rolling, and annealing. Copper material shall meet the maximum limit of electrical resistivity as indicated. The material shall undergo tensile strength, Rockwell hardness, and plate item tests to conform with the mechanical proptery requirement of the specification. The material shall also be capable of passing microscopical examination and embrittlement test, but not required by the specification.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification2 establishes the requirements for copper sheet, strip, plate, and rolled bar produced from the following coppers.
Copper | Previous | Type of Copper |
|
|
|
C10100B | OFE | Oxygen-free electronic |
C10200B | OF | Oxygen-free without residual |
C10300 | OFXLP | Oxygen-free extra low phosphorus |
C10400, C10500, C10700 | OFS | Oxygen-free, silver bearing |
C10800 | OFLP | Oxygen-free low phosphorus |
C10910 | ... | Low oxygen |
C11000B, C | ETP, | Electrolytic tough pitch,C Tough pitchC |
C11300, C11400, C11600B | STP | Silver bearing tough pitch |
C12000 | DLP | Phosphorized, low residual phos- |
C12200B | DHP | Phosphorized, high residual phos- |
C12300 | DHPS | Phosphorized, silver bearing |
C14200 | DPA | Phosphorus deoxidized, arsenical |
C14420 | ... | Tin bearing tellurium copper |
C14530 | ... | Tin tellurium bearing copper |
Note 1: Each of the coppers listed has unique properties that can make it suitable for specific applications. The purchaser should consult with the supplier to determine which copper would be best suited for the intended application.
Note 2: This specification is not intended to establish requirements for material rolled to ounce-weight thicknesses. Such material is defined in Specification B370.
Flat copper products with finished (rolled or drawn) edges (flat wire and strip) are defined in Specification B272.
1.1.1 When a specific copper is not identified in the contract or purchase order, the supplier may furnish product from any of the listed coppers.
1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other and values from the two systems shall not be combined.
1.3 The following safety hazard caveat pertains only to the test method(s) described in this specification:
1.3.1 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B170 Specification for Oxygen-Free Electrolytic CopperRefinery Shapes
B193 Test Method for Resistivity of Electrical Conductor Materials
B216 Specification for Tough-Pitch Fire-Refined CopperRefinery Shapes
B224 Classification of Coppers
B248 Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar
B248M Specification for General Requirements for Wrought Copper and Copper-Alloy Plate, Sheet, Strip, and Rolled Bar (Metric)
B272 Specification for Copper Flat Products with Finished (Rolled or Drawn) Edges (Flat Wire and Strip)
B370 Specification for Copper Sheet and Strip for Building Construction
B577 Test Methods for Detection of Cuprous Oxide (Hydrogen Embrittlement Susceptibility) in Copper
B846 Terminology for Copper and Copper Alloys
E3 Guide for Preparation of Metallographic Specimens
E8/E8M Test Methods for Tension Testing of Metallic Materials
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E112 Test Methods for Determining Average Grain Size
E478 Test Methods for Chemical Analysis of Copper Alloys
ICS Code
ICS Number Code 77.150.30 (Copper products)
UNSPSC Code
UNSPSC Code 30262300(Copper sheets); 30102209(Copper plate)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0152_B0152M-19
Citation Format
ASTM B152 / B152M-19, Standard Specification for Copper Sheet, Strip, Plate, and Rolled Bar, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top