ASTM B127 - 19
Standard Specification for Nickel-Copper Alloy Plate, Sheet, and Strip
| Format | Pages | Price | ||
 |
7 | $52.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 7 | $52.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
14 | $62.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More B02.07 Standards Related Products Standard References
Abstract
This specification covers rolled nickel-copper alloy (UNS N04400) plate, sheet, and strip. The matreial shall conform to the required chemical composition for nickel, copper, iron, manganese, carbon, silicon, and sulfur. The material shall conform to the required mechanical propeties such as tensile strength, yield strength, elongation, and Rockwell hardness. The material shall conform to the required grain size. Dimensions such as plate, sheet, and strip thickness, width, or diameter, length, straightness, edges, squareness, and flatness shall be determined.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification2 covers rolled nickel-copper alloy (UNS N04400)3 plate, sheet, and strip.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Federal Standards
Fed. Std. No. 102 Preservation, Packaging, and Packing Levels Fed. Std. No. 123 Marking for Shipment (Civil Agencies) Fed. Std. No. 182 Continuous Identification Marking of Nickel and Nickel-Base AlloysMilitary Standards
MIL-STD-129 Marking for Shipment and Storage MIL-STD-271 Nondestructive Testing Requirements for MetalsASTM Standards
B906 Specification for General Requirements for Flat-Rolled Nickel and Nickel Alloys Plate, Sheet, and Strip
E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness
F155 Method of Test for Temper of Strip and Sheet Metals for Electronic Devices (Spring-Back Method)
ICS Code
ICS Number Code 77.150.40 (Nickel and chromium products)
UNSPSC Code
UNSPSC Code 30266204(Non ferrous alloy strip); 30266103(Non ferrous alloy sheet)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0127-19
Citation Format
ASTM B127-19, Standard Specification for Nickel-Copper Alloy Plate, Sheet, and Strip, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top