ASTM B1009 - 18

    Standard Specification for Titanium Alloy Bars for Near Surface Mounts in Civil Structures

    Active Standard ASTM B1009 | Developed by Subcommittee: B10.01

    Book of Standards Volume: 02.04


      Format Pages Price  
    PDF 5 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $48.00   ADD TO CART



    1. Scope

    1.1 This specification covers titanium alloy bars with surface deformations and 90-degree anchorage hooks for use as near surface mounts for flexural and shear strengthening of concrete beams. The product can be furnished with or without anchorage hooks as specified by the purchaser. If supplied without hooks, the hooks shall be bent on-site prior to installation, as this method requires two 90-degree anchorage hooks.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A944 Test Method for Comparing Bond Strength of Steel Reinforcing Bars to Concrete Using Beam-End Specimens

    B348 Specification for Titanium and Titanium Alloy Bars and Billets

    D7913/D7913M Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing

    E8/E8M Test Methods for Tension Testing of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E539 Test Method for Analysis of Titanium Alloys by X-Ray Fluorescence Spectrometry

    E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by Inert Gas Fusion

    E1447 Test Method for Determination of Hydrogen in Titanium and Titanium Alloys by Inert Gas Fusion Thermal Conductivity/Infrared Detection Method

    E1941 Test Method for Determination of Carbon in Refractory and Reactive Metals and Their Alloys by Combustion Analysis

    E2371 Test Method for Analysis of Titanium and Titanium Alloys by Direct Current Plasma and Inductively Coupled Plasma Atomic Emission Spectrometry (Performance-Based Test Methodology)

    E2626 Guide for Spectrometric Analysis of Reactive and Refractory Metals

    E2994 Test Method for Analysis of Titanium and Titanium Alloys by Spark Atomic Emission Spectrometry and Glow Discharge Atomic Emission Spectrometry (Performance-Based Method)

    ACI Standard

    ACI 318 Building Code Requirements for Structural Concrete


    ICS Code

    ICS Number Code 77.150.50 (Titanium products)

    UNSPSC Code

    UNSPSC Code 30262000(Titanium bars and sheets)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/B1009-18

    Citation Format

    ASTM B1009-18, Standard Specification for Titanium Alloy Bars for Near Surface Mounts in Civil Structures, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top