| Format | Pages | Price |   |
![]() |
5 | $50.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 5 | $50.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
10 | $60.00 | ![]() |
Historical Version(s) - view previous versions of standard
More A01.22 Standards Related Products Standard References
Abstract
This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems. Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products with filler metal added. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. Specimens shall conform to required values of chemical composition and mechanical properties, namely: yield strength, tensile strength, elongation, notch toughness, and hardness. This specification does not require hydrostatic testing.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers wrought high-strength ferritic steel butt-welding fittings of seamless and electric fusion-welded construction. Dimensions of the fittings are provided in the latest revisions of ASME B16.9 and MSS-SP-75. Butt-welding fittings differing from ASME B16.9 shall be furnished in accordance with Supplementary Requirement S58 of Specification A960/A960M. These fittings are for use in high-pressure gas and oil transmission and distribution systems.
1.2 Optional supplementary requirements are provided for fittings when a greater degree of examination is desired. One or more of the supplementary requirements may be specified in the order.
1.3 This specification does not cover cast-welding fittings or fittings machined from castings.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
MSS Standards
MSS SP-25 The Standard Marking System of Valves, Fittings, Flanges and Unions MSS-SP-75 Specification for High Test Wrought Butt-Welding FittingsAmerican Society of Nondestructive Testing
SNT-TC-1A Recommended Practice for Nondestructive Testing Personnel Qualification and CertificationASME Boiler and Pressure Vessel Code
Section IX Section VASTM Standards
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
ICS Code
ICS Number Code 23.040.40 (Metal fittings)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A0860_A0860M-18
Citation Format
ASTM A860 / A860M-18, Standard Specification for Wrought High-Strength Ferritic Steel Butt-Welding Fittings, ASTM International, West Conshohocken, PA, 2018, www.astm.org
Back to Top