If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM A742 / A742M - 20
Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe
| Format | Pages | Price | ||
 |
4 | $46.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 4 | $46.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
8 | $54.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More A05.17 Standards Related Products Standard References
Abstract
This specification covers polymer precoated steel sheet for corrugated steel pipe (CSP) which is coated after metallic coating on continuous lines by coil coating (roller coating or laminating) processes. The metallic coating shall either be zinc, aluminum-zinc alloy, or zinc-aluminum-mischmetal alloy. Sheet for this purpose shall be furnished flat in coils, flat in cut lengths, or corrugated in cut lengths, all being protected by a mill-applied polymer coating on both sides. The polymer coating shall be classified by grade corresponding to the thickness on each side. Requirements for the cleaning process of the steel sheet and for the polymer coating are given. The test methods for the following polymer coating properties are detailed: adhesion, impact, thickness, holidays, abrasion resistance, imperviousness, freeze-thaw resistance, weatherability, and resistance to microbial attack.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers polymer precoated steel sheet for corrugated steel pipe (CSP) which is coated after metallic coating on continuous lines by coil coating (roller coating or laminating) processes. The metallic coating is either zinc, 55 % aluminum-zinc alloy, or zinc-5 % aluminum-mischmetal alloy. Sheet for this purpose is furnished flat in coils, flat in cut lengths, or corrugated in cut lengths, all being protected by a mill-applied polymer coating on both sides.
1.2 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.3 The following precautionary caveat refers only to the test method portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A929/A929M Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D968 Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers
D2794 Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D7091 Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
G62 Test Methods for Holiday Detection in Pipeline Coatings
G152 Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
ICS Code
ICS Number Code 77.140.50 (Flat steel products and semi-products)
UNSPSC Code
UNSPSC Code 40170000(Pipe piping and pipe fittings)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A0742_A0742M-20
Citation Format
ASTM A742 / A742M-20, Standard Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top