Products and Services / Standards & Publications / Standards Products


    ASTM A705 / A705M - 13

    Standard Specification for Age-Hardening Stainless Steel Forgings

    Active Standard ASTM A705 / A705M | Developed by Subcommittee: A01.17

    Book of Standards Volume: 01.03

      Format Pages Price  
    PDF 8 $45.00   ADD TO CART
    Hardcopy (shipping and handling) 8 $45.00   ADD TO CART
    Standard + Redline PDF Bundle 16 $54.00   ADD TO CART

    Reprints and Permissions

    Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center  

    Rent This Document            
    Reprints and Permissions  

    Reprints, Permissions and Rentals

    Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center  

    Rent This Document            

    Reprints and Permissions  

    Historical Version(s) - view previous versions of standard

    ASTM License Agreement

    Shipping & Handling

    More A01.17 Standards Related Products Standard References

    Abstract

    This specification covers age-hardening stainless steel forgings for general use. Materials for forgings shall consist of billets or bars and shall either be forged, rolled, or cast or a section cut from an ingot. The steel specimens shall be solution annealed and age hardened and shall conform to the required values of tensile strength, yield strength, elongation, reduction of area, hardness and impact Charpy-V. The steel materials shall conform to the required chemical compositions of carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, aluminum, molybdenum, titanium, copper, nitrogen, columbium, and tantalum.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification2 covers age-hardening stainless steel forgings for general use.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.

    Note 1—Bar products are covered by Specification A564/A564M.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A484/A484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings

    A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    Other Documents

    SAE J 1086 Recommended Practice for Numbering Metals and Alloys (UNS)

    ICS Code

    ICS Number Code 77.140.85 (Iron and steel forgings)

    UNSPSC Code

    UNSPSC Code 31132600(Stainless steel forgings)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0705_A0705M

    Citation Format

    ASTM A705 / A705M-13, Standard Specification for Age-Hardening Stainless Steel Forgings, ASTM International, West Conshohocken, PA, 2013, www.astm.org

    Back to Top