ASTM A648 - 18

    Standard Specification for Steel Wire, Hard-Drawn for Prestressed Concrete Pipe

    Active Standard ASTM A648 | Developed by Subcommittee: A01.05

    Book of Standards Volume: 01.04


      Format Pages Price  
    PDF 5 $46.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $46.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $55.20   ADD TO CART



    Abstract

    This specification covers two classes of uncoated, high-strength, hard-drawn steel wires for use in the manufacture of prestressed concrete pipe. The steel shall be made by the open-hearth, basic-oxygen, or electric-furnace process, and shall be free of injurious piping and undue segregation. The wire shall be cold drawn to produce the desired mechanical properties and there shall be no welds or joints in the finished wire. Cast or heat analysis of the steel shall conform to the chemical requirements specified for carbon, manganese, phosphorus, sulfur, silicon, and nitrogen. The tension and relaxation tests shall conform to the specified tensile requirements including tensile strength and breaking strength. Torsion test shall also be performed where test specimens shall be inspected for primary break shear area and longitudinal (spiral) splitting following completion of the test.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers two classes of uncoated, high-strength, hard-drawn steel wire for use in the manufacture of prestressed concrete pipe. In application, the wire is helically wrapped on the pipe maintaining tension by mechanical means not including drawing dies.

    1.2 A supplementary requirement (S1) is provided for use where hydrogen embrittlement (HE) resistance testing is required by the purchaser. Supplementary requirement (S1), which establishes acceptance criteria for HE resistance testing, applies only when specified in the purchase order or contract.

    1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.4 The following caveat pertains only to the test method portions of this specification, 6.3.3 and 6.5.3: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A510 Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel

    A700 Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1032 Test Method for Hydrogen Embrittlement Resistance for Steel Wire Hard-Drawn Used for Prestressed Concrete Pipe

    E328 Test Methods for Stress Relaxation for Materials and Structures

    ANSI Standard


    ICS Code

    ICS Number Code 77.140.15 (Steels for reinforcement of concrete)

    UNSPSC Code

    UNSPSC Code 31152207(Prestressed concrete steel wire)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0648-18

    Citation Format

    ASTM A648-18, Standard Specification for Steel Wire, Hard-Drawn for Prestressed Concrete Pipe, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top