ASTM A36 / A36M - 19

    Standard Specification for Carbon Structural Steel

    Active Standard ASTM A36 / A36M | Developed by Subcommittee: A01.02

    Book of Standards Volume: 01.04


      Format Pages Price  
    PDF 3 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $42.00   ADD TO CART
    Standard + Redline PDF Bundle 6 $50.00   ADD TO CART



    Abstract

    This specification covers carbon structural steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes. Heat analysis shall be used to determine the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, and copper. Tensile strength, yield strength, and elongation shall be evaluated using tension test and must conform to the required tensile properties.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification2 covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.

    1.2 Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. Such requirements apply only when specified in the purchase order.

    1.3 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

    1.4 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

    1.5 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply.

    1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.

    1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A6/A6M Specification for General Requirements for Rolled Structural Steel Bars, Plates, Shapes, and Sheet Piling

    A27/A27M Specification for Steel Castings, Carbon, for General Application

    A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60000 PSI Tensile Strength

    A500 Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

    A501 Specification for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

    A502 Specification for Rivets, Steel, Structural

    A563 Specification for Carbon and Alloy Steel Nuts

    A563M Specification for Carbon and Alloy Steel Nuts (Metric)

    A668/A668M Specification for Steel Forgings, Carbon and Alloy, for General Industrial Use

    A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

    A1018/A1018M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Carbon, Commercial, Drawing, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

    F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)

    F1554 Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength

    F3125/F3125M Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength


    ICS Code

    ICS Number Code 77.140.10 (Heat-treatable steels)

    UNSPSC Code

    UNSPSC Code 30260000(Structural materials); 11101704(Steel)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0036_A0036M-19

    Citation Format

    ASTM A36 / A36M-19, Standard Specification for Carbon Structural Steel, ASTM International, West Conshohocken, PA, 2019, www.astm.org

    Back to Top