If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
ASTM A302 / A302M - 17
Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel
| Format | Pages | Price | ||
 |
3 | $46.00 |  ADD TO CART |
|
 |
Hardcopy (shipping and handling) | 3 | $46.00 | ADD TO CART |
|
Standard + Redline PDF Bundle  |
6 | $54.00 | ADD TO CART |
Historical Version(s) - view previous versions of standard
More A01.11 Standards Related Products Standard References
Abstract
This specification covers manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates intended particularly for welded boilers and other pressure vessels. According to their strength levels, the plates are available in four grades: Grades A, B, C, and D. The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements. The steel shall be killed and shall conform to fine grain size requirements. The plates shall be subjected to tension test to determine the tensile strength, yield strength, and elongation.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification2 covers manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates intended particularly for welded boilers and other pressure vessels.
1.2 Plates under this specification are available in four grades having different strength levels as follows:
| Grade | Tensile Strength, | Type |
| A | 75–95 [515–655] | manganese-molybdenum |
| B | 80–100 [550–690] | manganese-molybdenum |
| C | 80–100 [550–690] | manganese-molybdenum-nickel |
| D | 80–100 [550–690] | manganese-molybdenum-nickel |
1.3 The maximum thickness of plates is limited only by the capacity of the chemical composition to meet the specified mechanical property requirements.
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A20/A20M Specification for General Requirements for Steel Plates for Pressure Vessels
A435/A435M Specification for Straight-Beam Ultrasonic Examination of Steel Plates
A577/A577M Specification for Ultrasonic Angle-Beam Examination of Steel Plates
A578/A578M Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
ICS Code
ICS Number Code 77.140.30 (Steels for pressure purposes); 77.140.50 (Flat steel products and semi-products)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A0302_A0302M-17
Citation Format
ASTM A302 / A302M-17, Standard Specification for Pressure Vessel Plates, Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel, ASTM International, West Conshohocken, PA, 2017, www.astm.org
Back to Top