Products and Services / Standards & Publications / Standards Products


    ASTM A209 / A209M - 03(2017)

    Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes

    Active Standard ASTM A209 / A209M | Developed by Subcommittee: A01.10

    Book of Standards Volume: 01.01

      Format Pages Price  
    PDF 3 $40.00   ADD TO CART
    Hardcopy (shipping and handling) 3 $40.00   ADD TO CART

    Reprints and Permissions

    Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center  

    Rent This Document            
    Reprints and Permissions  

    Reprints, Permissions and Rentals

    Rental access and permissions to reprint documents can be acquired through Copyright Clearance Center  

    Rent This Document            

    Reprints and Permissions  

    Historical Version(s) - view previous versions of standard

    ASTM License Agreement

    Shipping & Handling

    More A01.10 Standards Related Products Standard References

    Abstract

    This specification covers seamless carbon-molybdenum alloy-steel boiler and superheater tubes. As a steel making practice, the steel material shall be killed. The required chemical composition for steel is given. The mechanical property requirements include tensile requirements and hardness requirements. Different test procedure shall be performed on the material presented, one tension test shall be made on a specimen for lots of not more than 50 tubes, one flattening test shall be made on specimens from each end of one finished tube, one flaring test shall be made on specimens from each end of one finished tube, and Brinell or Rockwell hardness tests shall be made from two tubes from each lot.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification2 covers several grades of minimum-wall-thickness, seamless, carbon-molybdenum alloy-steel, boiler and superheater tubes.

    1.2 This specification covers tubes 1/2 to 5 in. [12.7 to 127 mm] inclusive, in outside diameter and 0.035 to 0.500 in. [0.9 to 12.7 mm], inclusive, in minimum wall thickness.

    1.3 An optional supplementary requirement is provided and, when desired, shall be so stated in the order.

    1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A1016/A1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes

    ICS Code

    ICS Number Code 23.040.10 (Iron and steel pipes)

    UNSPSC Code

    UNSPSC Code 40182300(Seamless steel tubes)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0209_A0209M-03R17

    Citation Format

    ASTM A209 / A209M-03(2017), Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes, ASTM International, West Conshohocken, PA, 2017, www.astm.org

    Back to Top