| Format | Pages | Price |   |
![]() |
3 | $46.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 3 | $46.00 | ![]() |
![]() |
Standard + Redline PDF Bundle ![]() |
6 | $54.00 | ![]() |
Historical Version(s) - view previous versions of standard
Translated Version(s):
Spanish
,
Brazilian Portuguese
More A01.05 Standards Related Products Standard References
Abstract
This specification covers the standard guide for welded deformed steel bar mats for concrete reinforcement. Mats should be capable of withstanding static load exerted perpendicular to the plane of the mat tending to separate the bars with no apparent loosening when applied to one intersection of the connected bars. Tension tests shall be performed on the specimen to determine the conformance to reference test materials. Also, test of connections against separation shall be performed on an assembled mat by placing blocks under a deformed bar in the upper layer and applying the prescribed load upon the bar in the lower layer.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers material in mat (or sheet) form fabricated from deformed steel bars to be used for the reinforcement of concrete. Mats are made from two layers of bars that are assembled by welding the intersections at right angles to each other.
1.2 This specification is applicable for orders in either inch-pound units (as Specification A184) or SI units (as Specification A184M).
1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with this specification.
1.4 The text of this specification references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
U.S. Federal Standard
Fed Std No. 123 Marketing for Shipments (Civil Agencies)U.S. Military Standard
MIL-STD-129 Marking for Shipment and StorageAWS Standard
AWS D1.4/D1.4M Structural Welding Code Steel Reinforcing BarsASTM Standards
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
ICS Code
ICS Number Code 77.140.15 (Steels for reinforcement of concrete)
UNSPSC Code
UNSPSC Code 30103623(Reinforcing bar or rebar or mesh)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A0184_A0184M-19
Citation Format
ASTM A184 / A184M-19, Standard Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement, ASTM International, West Conshohocken, PA, 2019, www.astm.org
Back to Top