| Format | Pages | Price |   |
![]() |
13 | $58.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 13 | $58.00 | ![]() |
1. Scope
1.1 This specification covers corrugated steel structural plate, polymer-coated, used in the construction of pipe, pipe-arches, arches, underpasses, and special shapes for field assembly. Appropriate fasteners and accessory materials are also described. The pipe, arches, and other shapes are generally used for drainage purposes, pedestrian and vehicular underpasses, and utility tunnels.
1.2 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and plate thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of plate thickness, type of bedding and backfill, manufacture in the plant, and care in the installation. The purchaser must correlate the preceding factors and also the corrosion and abrasion requirements of the field installation with the plate thickness. The structural design of corrugated steel structural plate pipe and the proper installation procedures are described in Practices A796/A796M and A807/A807M.
1.3 Units—This specification is applicable to orders in either inch-pound units (as A1113) or SI units (as A1113M). Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text, but they are the applicable values when the material is ordered to A1113M.
1.4 This specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A36/A36M Specification for Carbon Structural Steel
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A761/A761M Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches
A796/A796M Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications
A807/A807M Practice for Installing Corrugated Steel Structural Plate Pipe for Sewers and Other Applications
D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents
D610 Practice for Evaluating Degree of Rusting on Painted Steel Surfaces
D638 Test Method for Tensile Properties of Plastics
D968 Test Methods for Abrasion Resistance of Organic Coatings by Falling Abrasive
D1654 Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments
D2794 Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)
D3359 Test Methods for Rating Adhesion by Tape Test
D4541 Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
D6677 Test Method for Evaluating Adhesion by Knife
D7091 Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
F1554 Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield Strength
G62 Test Methods for Holiday Detection in Pipeline Coatings
ANSI Standards
B18.2.1 Square and Hex Bolts and Screws, Inch Series B18.2.2 B18.2.3.4M Bolts, Metric Heavy Hex B18.2.4.6MAWS Standard
AWS D1.1/D1.1M Structural Welding CodeGM Standard
GMW14872 Cyclic Corrosion Laboratory TestSAE Standard
SAE J2334 Laboratory Cyclic Corrosion TestLink Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A1113_A1113M-20
Citation Format
ASTM A1113 / A1113M-20, Standard Specification for Corrugated Steel Structural Plate, Polymer-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top