If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass
    ASTM A1110 / A1110M - 18

    Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes with 52 KSI [360 MPa] Minimum Yield Strength and Impact Requirements

    Active Standard ASTM A1110 / A1110M | Developed by Subcommittee: A01.09

    Book of Standards Volume: 01.01


      Format Pages Price  
    PDF 5 $52.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $52.00   ADD TO CART



    1. Scope

    1.1 This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes where impact properties are required.

    1.2 This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall thickness from 0.148 in. [4 mm] up to 0.875 in. [22 mm].

    1.3 The welded and seamless tubing can be supplied in two different grades each with a specified impact test temperature. Different strength levels, CVN acceptance criteria, and impact test temperatures than listed may be available. To determine their availability, the purchaser should contact the producer (see 4.1.4 and 4.1.13).

    1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.

    1.5 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

    1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A370 Test Methods and Definitions for Mechanical Testing of Steel Products

    A700 Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys

    A1058 Test Methods for Mechanical Testing of Steel Products--Metric

    Federal Standards

    Fed. Std. No. 123 Marking for Shipment

    Military Standards

    MIL-STD-129 Marking for Shipment and Storage Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A1110_A1110M-18

    Citation Format

    ASTM A1110 / A1110M-18, Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes with 52 KSI [360 MPa] Minimum Yield Strength and Impact Requirements, ASTM International, West Conshohocken, PA, 2018, www.astm.org

    Back to Top