ASTM A1091 / A1091M - 16e1

    Standard Specification for Steel Castings, Creep-Strength Enhanced Ferritic Alloy, for Pressure-Containing Parts, Suitable for High Temperature Service

    Active Standard ASTM A1091 / A1091M | Developed by Subcommittee: A01.18

    Book of Standards Volume: 01.02


      Format Pages Price  
    PDF 5 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $48.00   ADD TO CART



    1. Scope

    1.1 This specification covers creep-strength enhanced alloy steel castings for valves, flanges, fittings, and other pressure-containing parts intended primarily for high-temperature service (see Note 1). However, they are not restricted to such applications, and the castings may be used for other applications for which the attributes of the material, as defined by this specification, are suitable.

    1.2 One grade of martensitic alloy steel, Grade C91, is covered (see Note 2). It is provided in two classes, differentiated by the type of heat treatment after weld repairs. This and similar steels are characterized by a predominantly tempered martensitic or tempered Bainitic microstructure that is stabilized by the precipitation of temper-resistant particles at various precipitate nucleation sites in the microstructure. Such steels are designed to have creep-rupture strengths significantly superior to those of alloys of nominally similar compositions, but in which the precipitates or nucleation sites are absent. Since this crucial difference cannot be revealed by room-temperature mechanical property tests, these alloys require tighter controls on manufacturing and processing.

    Note 1: The grades covered by this specification represent materials that are generally suitable for assembly with other castings or wrought steel parts by fusion welding. It is not intended to imply that these grades possess equal degrees of weldability; therefore, it is the responsibility of the purchaser to establish a suitable welding technique. Since these grades possess varying degrees of suitability for high-temperature service, it is also the responsibility of the purchaser to determine which grade shall be furnished, due consideration being given to the requirements of the applicable construction codes.

    Note 2: The committee formulating this specification has included one grade of material that is considered to represent a type of ferritic alloy steel suitable for valves, flanges, fittings, and other pressure-containing parts. Additional alloy steels will be considered for inclusion in this specification by the committee as the need becomes apparent.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A335/A335M Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service

    A703/A703M Specification for Steel Castings, General Requirements, for Pressure-Containing Parts

    A802/A802M Practice for Steel Castings, Surface Acceptance Standards, Visual Examination

    A985/A985M Specification for Steel Investment Castings General Requirements, for Pressure-Containing Parts

    A999/A999M Specification for General Requirements for Alloy and Stainless Steel Pipe

    ANSI Standards

    ANSI B46.1 Surface Texture

    ASME Boiler and Pressure Vessel Code

    ASME Boiler and Pressure Vessel Code

    ASME Boiler and Pressure Vessel Code Section III

    ASME Boiler and Pressure Vessel Code Section VIII

    ASME Boiler and Pressure Vessel Code Section XII


    ICS Code

    ICS Number Code 77.140.80 (Iron and steel castings)

    UNSPSC Code

    UNSPSC Code


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A1091_A1091M-16E01

    Citation Format

    ASTM A1091 / A1091M-16e1, Standard Specification for Steel Castings, Creep-Strength Enhanced Ferritic Alloy, for Pressure-Containing Parts, Suitable for High Temperature Service, ASTM International, West Conshohocken, PA, 2016, www.astm.org

    Back to Top