| ||Format||Pages||Price|| |
|3||$44.00||  ADD TO CART|
|Hardcopy (shipping and handling)||3||$44.00||  ADD TO CART|
|Standard + Redline PDF Bundle||6||$52.00||  ADD TO CART|
This specification covers electric-resistance-welded structural tubing with round, square, rectangular, and special shapes and produced from precoated sheet steel with zinc (galvanized) or 55% aluminum-zinc alloy as coatings on both sides. This product is intended for applications requiring minimum mechanical properties and corrosion resistance of both exterior and interior surfaces. The standard addresses product size, material classification, ordering information, coating properties, chemical composition, mechanical properties of finished tube, flattening test, and oiling.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers round, square, rectangular, and special shape, electric-resistance-welded structural tubing produced from precoated sheet steel with the following coatings on both sides: zinc (galvanized) or 55% aluminum-zinc alloy or zinc-5 % aluminum alloy-coated. This product is intended for applications requiring minimum mechanical properties and corrosion resistance of both exterior and interior surfaces.
1.2 This specification covers:
1.2.1 Three grades of round tubing and three grades of shaped tubing, identified in (Chemical Requirements), (Mechanical Requirements of Round Structural Tubing), and (Mechanical Requirements of Shaped Structural Tubing).
1.2.2 Three different types of coating composition/designations (Section ).
1.3 This specification is applicable to orders in either inch-pound units (as A1076) or SI units (as A1076M). Within the text, SI units are shown in brackets. The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A500/A500M Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process
A792/A792M Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
A875/A875M Specification for Steel Sheet, Zinc-5 % Aluminum Alloy-Coated by the Hot-Dip Process
A902 Terminology Relating to Metallic Coated Steel Products
A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
B750 Specification for GALFAN (Zinc-5% Aluminum-Mischmetal) Alloy in Ingot Form for Hot-Dip Coatings,
ICS Number Code 23.040.10 (Iron and steel pipes)
UNSPSC Code 40181800(Welded steel tubes)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A1076 / A1076M-20, Standard Specification for Cold Formed Carbon Structural Steel Tubing Made from Metallic Precoated Sheet Steel, ASTM International, West Conshohocken, PA, 2020, www.astm.orgBack to Top