| ||Format||Pages||Price|| |
|10||$52.00||  ADD TO CART|
|Hardcopy (shipping and handling)||10||$52.00||  ADD TO CART|
|Standard + Redline PDF Bundle||20||$62.00||  ADD TO CART|
This specification covers steel sheet in coils and cut lengths coated with zinc-aluminum-magnesium alloy by hot-dip process intended for applications requiring corrosion resistance and paintability. The steel sheet shall be produced in the following designations: commercial steel (CS types A,B,C), forming steel (FS type A and B), deep drawing steel (DDS), extra deep drawing steel (EDDS), structural steel (SS), high strength low alloy steel (HSLAS), and high strength low alloy steel with improved formability (HSLAS-F). Structural steel and high strength low alloy steel shall be available in several grades based on mechanical properties such as yield strength, tensile strength, and elongation. Structural steel Grade 50  shall be available in four classes based on tensile strength. The coating weights [masses] shall conform to the specified requirements determined by triple-spot and single-spot tests. The coating bath composition and the method of estimating the coating thickness from the coating weight [mass] are given. Heat analysis of the base metal shall conform to the chemical requirements prescribed for carbon, manganese, phosphorous, sulfur, aluminum, copper, nickel, chromium, molybdenum, vanadium, columbium, and titanium. Bending properties of the base metal including minimum cold bending radii and cracks, and the coating bend test requirements are detailed.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers zinc-aluminum-magnesium alloy-coated steel sheet in coils and cut lengths.
1.2 This product is intended for applications requiring corrosion resistance and paintability.
1.3 The steel sheet is produced in a number of designations, types, grades, and classes designed to be compatible with differing application requirements.
1.4 Product furnished under this specification shall conform to the applicable requirements of the latest issue of Specification , unless otherwise provided herein.
1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes, excluding those in tables and figures, shall not be considered as requirements of the standard.
1.6 This specification is applicable to orders in either inch-pound units (as ) or SI units (as ). Values in inch-pound and SI units are not necessarily equivalent. Within the text, SI units are shown in brackets. Each system shall be used independently of the other.
1.7 Unless the order specifies the “M” designation (SI units), the product shall be furnished to inch-pound units.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
A902 Terminology Relating to Metallic Coated Steel Products
A924/A924M Specification for General Requirements for Steel Sheet, Metallic-Coated by the Hot-Dip Process
E517 Test Method for Plastic Strain Ratio r for Sheet Metal
E646 Test Method for Tensile Strain-Hardening Exponents (n -Values) of Metallic Sheet Materials
ICS Number Code 77.140.50 (Flat steel products and semi-products)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A1046 / A1046M-19, Standard Specification for Steel Sheet, Zinc-Aluminum-Magnesium Alloy-Coated by the Hot-Dip Process, ASTM International, West Conshohocken, PA, 2019, www.astm.orgBack to Top