| Format | Pages | Price |   |
![]() |
4 | $46.00 | ![]() |
|
![]() |
Hardcopy (shipping and handling) | 4 | $46.00 | ![]() |
Historical Version(s) - view previous versions of standard
More A01.18 Standards Related Products Standard References
Abstract
This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials. The chemical analysis method shall be agreed upon by the purchaser and supplier. Unless otherwise specified, the material shall be sampled for determination of chemical composition and size.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers a group of common requirements that, unless otherwise specified in an individual specification, shall apply to ferroalloys and other alloying materials under each of the following ASTM specifications:
Title of Specification | ASTM Designation |
Ferromanganese | A99 |
Ferrosilicon | A100 |
Ferrochromium | A101 |
Ferrovanadium | A102 |
Ferromolybdenum | A132 |
Molybdenum Oxide Products | A146 |
Ferroboron | A323 |
Ferrotitanium | A324 |
Chromium Metal | A481 |
Ferrochrome-Silicon | A482/A482M |
Silicomanganese | A483/A483M |
Calcium-Silicon Alloys | A495 |
Ferrocolumbium | A550 |
Electrolytic Manganese Metal | A601/A601M |
Nickel Oxide Sinter | A636 |
Ferromanganese Silicon | A701/A701M |
Titanium Scrap for Use in Deoxidation and Alloying of Steel | A845 |
Aluminum Scrap for Use in Deoxidation and Alloying of Steel | A846 |
Silicon Metal | A922 |
1.2 This specification also covers a group of supplementary requirements which may be applied to the above specifications as indicated therein. These are provided for use when additional testing or inspection is desired and apply only when specified individually by the purchaser in the order.
1.3 In case of conflict between the requirements of the individual specification and this general specification, the former shall prevail.
1.4 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4.1 This specification is expressed in both inch-pound units and in SI units (within the text, the SI units are shown in brackets); however, unless the purchase order or contract specifies the applicable M specification designation (SI units), the inch-pound units shall apply.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A99 Specification for Ferromanganese
A100 Specification for Ferrosilicon
A101 Specification for Ferrochromium
A102 Specification for Ferrovanadium
A132 Specification for Ferromolybdenum
A146 Specification for Molybdenum Oxide Products
A323 Specification for Ferroboron
A324 Specification for Ferrotitanium
A481 Specification for Chromium Metal
A482/A482M Specification for Ferrochrome-Silicon
A483/A483M Specification for Silicomanganese
A495 Specification for Calcium-Silicon Alloys
A550 Specification for Ferrocolumbium (Ferroniobium)
A601/A601M Specification for Electrolytic Manganese Metal
A610 Test Methods for Sampling and Testing Ferroalloys for Determination of Size
A636 Specification for Nickel Oxide Sinter
A701/A701M Specification for Ferromanganese-Silicon
A845 Specification for Titanium Scrap for Use in Deoxidation and Alloying of Steel
A846 Specification for Aluminum Scrap for Use in Deoxidation and Alloying of Steel
A922 Specification for Silicon Metal
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E32 Practices for Sampling Ferroalloys and Steel Additives for Determination of Chemical Composition
ICS Code
ICS Number Code 77.100 (Ferroalloys)
UNSPSC Code
UNSPSC Code
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A1025_A1025M-10R20
Citation Format
ASTM A1025 / A1025M-10(2020), Standard Specification for Ferroalloys and Other Alloying Materials, General Requirements, ASTM International, West Conshohocken, PA, 2020, www.astm.org
Back to Top