D02 Petroleum Products and Lubricants

    Title: Workshop on FZG Gear Lubricant Tests and Gear Rating

    Dates: Thursday June 28 2018

    Location: JW Marriott Phoenix Desert Ridge; Phoenix, AZ

    Event Name: D02 June 2018 Meeting

    About The Event

    Registration Information

    Continuing Education Units

    Technical Chair Contact Information

    Hotel Information

    Dress and Weather

    Standards Development Meetings

    Future Meeting Dates

    Miscellaneous


    About the Event

    The Workshop on FZG Gear Lubricant Tests and Gear Rating will be held Thursday, June 28, 2018. Sponsored by ASTM Committee D02 L11 on Tribiological Properties of Industrial Fluids and Lubricates, the workshop will be held at the JW Marriott Desert Ridge in Phoenix, AZ, in conjunction with the June standards development meetings of the committee.

    Objective
    Base oil type, oil viscosity and additive type and content have a strong influence on typical gear failure modes like scuffing, wear, micro-pitting and pitting. In general it is not possible to quantify the lubricant influence on the gear load carrying capacity simply from the knowledge of physical or chemical oil data. Therefore a number of adequate test methods based on the FZG back-to-back gear test rig were developed for evaluating the lubricant performance.

    Within the workshop the FZG gear test rig and widely used FZG test methods for gear lubricants will be introduced. For each test method requirements regarding test preparation, test course, documentation and test evaluation will be presented and discussed in detail. Furthermore, examples of failed gears will demonstrate the applicable rating procedures. A physical rating of some example gears amongst the participants will be performed.

    Course outline:

    • Introduction of FZG back-to-back gear test rig (standard set-up and modifications)
    • Overview of FZG test methods (general requirements)
    • Basics of main gear failure modes
    • FZG test methods and gear rating:
      • FZG scuffing tests
      • FZG wear tests
      • FZG micro-pitting tests
      • FZG pitting tests

      Why it is important to attend?

      The results of FZG tests allow gear designers to select adequate gear lubricants for an optimized gear load carrying capacity. FZG tests are therefore included in many technical specifications in the worldwide gear industry for different industrial applications. In order to obtain reliable and comparable results the test operators have to take care about the requirements on test rig, test parts and the different test procedures. They also should know about critical influence parameters and should be able to perform the required visual rating in accordance to the test specifications. The workshop will help participants to create and to evaluate test results with high precision and of increased reliability.

      Who should attend?

      • Test rig operators and technicians who perform FZG gear lubricant tests
      • Lab personnel who perform or are involved in the rating of results from FZG tests
      • Lab managers who are responsible for the results from FZG tests
      • Chemists who are involved in gear lubricant developing work
      • Engineers and gear designers who have to deal with the results of FZG tests for their work
      • Engineers who are responsible for developing gear lubricant specifications

      Registration Information

      Online registration is now open and closes June 20, 2018. There is no fee to attend the workshop.

      All attendees, including presenters and ASTM members, are urged to register online for this event so that space requirements can be accommodated. If you do not register online by the closing date, then you must register upon arrival at the workshop. All attendees must check in at the ASTM registration desk upon arrival at workshop.

      Cancellation
      To cancel your registration and request a refund, please contact Symposia Operations at symposia@astm.org or 610-832-9568.

      If you have questions concerning online registration, please contact Tessa Sulkes in Symposia Operations at symposia@astm.org Tel: 610-832-9677, or ASTM Technical Support at support@astm.org or 1-877-909-2786 (domestic) or 610-832-9578 (international).

      Online On Site
      ASTM Member FeeWaivedWaived
      Non-Member FeeWaivedWaived
      Presenter FeeWaivedWaived
      Student FeeWaivedWaived

      Continuing Education Units

      Workshop attendees interested in receiving 0.7 Continuing Education Units (CEUs) should complete a CEU application form at the adjournment of the workshop, and then submit it to the ASTM staff member on site. A certificate will be sent to the attendee approximately 4 to 6 weeks after the workshop.


      Technical Chair Contact Information

      Additional information about the workshop is available from Workshop Chairman:

      Dr.-Ing. Thomas Tobie
      Lehrstuhl fuer Maschinenelemente
      FZG - Forschungsstelle fuer Zahnraeder und Getriebebau
      Technische Universitaet Muenchen
      Boltzmannstrasse 15
      85748 Garching

      Tel.: +49-89-289-15830
      Fax: +49-89-289-15808
      Email: tobie@fzg.mw.tum.de


      Hotel Information

      All meetings will be held at the JW Marriott Phoenix Desert Ridge, 5350 East Marriott Drive, Phoenix, Arizona, 85054. Reservations may be made by telephoning the hotel at +1.480.293.5000. To make your hotel reservation online, visit: JW Marriott Phoenix Desert Ridge Reservations. Select your dates and proceed as instructed. If you need assistance with your hotel reservation, call the hotel directly.

      Group rate will be honored until the ASTM block is full, but no later than May 25, 2018. Reserved rooms may be SOLD OUT prior to the cut-off date. You may be charged a higher rate if reservations are received after the cut-off date. ASTM rates are $169 USD single/double, plus tax (you must mention ASTM in order to receive the group rate).

      U.S. GOVERNMENT RATES: The JW Marriott Phoenix Desert Ridge has a limited number of rooms at the government per diem rate. To make your hotel reservation online, visit: JW Marriott Phoenix Desert Ridge Government Reservations.

      The JW Marriott Phoenix Desert Ridge is sold out on certain nights.

      OVERFLOW HOTEL:

      Holiday Inn Express & Suites Phoenix North-Scottsdale
      4575 E Irma Lane
      Phoenix, AZ 85050

      Rate: $89. Rate includes breakfast buffet, Wi-Fi & self-parking.
      +1.833.259.3117. Please mention the D02 June Committee Meetings (Group code - D02)

      To make your hotel reservation online, visit: Holiday Inn Express & Suites Phoenix North-Scottsdale Reservations.

      IMPORTANT! ASTM rates are non-commissionable. If you book your reservation through a travel agent they must ask for a non-commissioned ASTM Group Rate. ASTM cannot adjust your higher rate if commissions were paid to a travel agency, or if you reserved a sleeping room outside of the ASTM group room block.

      ADVANCE DEPOSIT/ CANCELLATION POLICY: A Guarantee Deposit equal to one night's room and tax will be charged to the card on file upon booking your reservation at both the JW Marriott Phoenix Desert Ridge and the Holiday Inn Express & Suites Phoenix North-Scottsdale. This deposit will be refundable should you cancel your reservation through the end of the business day on April 27, 2018. Deposits will be non-refundable for any cancellations made on or after April 28, 2018.

      CONFIRMATION NOTICES: A confirmation number is provided to you electronically once your reservation has been submitted.

      INTERNET: The JW Marriott Phoenix Desert Ridge offers complimentary wireless connections in public spaces. The hotel charges $14.95 per day in guest rooms.

      Marriott Rewards Program: All Rewards members enjoy free in-room Wi-Fi when they book directly on Marriott.com, Marriott’s mobile app, 1-800 MARRIOTT or through a Marriott hotel. If you are not already a member, you may join here: Marriott Rewards Member.

      ASTM MEMBERS WORK AREA: ASTM provides computers with an internet connection. This area will also be wireless. You may visit the ASTM website, apply or renew your membership, order publications or check your email.


      Dress and Weather

      Attendees have the option to determine their dress at ASTM meetings. Business casual attire is acceptable at this meeting and appropriate for Phoenix. The average temperatures in June range from a high of 104 degrees Fahrenheit to a low of 76 degrees Fahrenheit.


      Standards Development Meetings

      Meeting schedules of Committee D02 are posted on the ASTM web site at www.astm.org/COMMIT/COMMITTEE/D02.htm or contact the ASTM staff manager, Alyson Fick at afick@astm.org or tel: 610-832-9710.


      Future Meeting Dates

      Committee D02 invites you to attend their future standards development meetings. There is no fee to attend these meetings, and membership in ASTM International is not required. For more information, visit the web page listed immediately above, and click on “Future Meetings”.


      Miscellaneous

      Please advise the hotel and ASTM of any disability which will require special attention. The JW Marriott Phoenix Desert Ridge is in compliance with ADA standards.


      Back to Top