General Products, Chemical Specialties, and End Use Products

    Effects of Fabrication Technique on Tensile Properties of Fiber Reinforced Polymer

    Challenges in Compression Testing of 3D Angle-Interlocked Woven-Glass Fabric-Reinforced Polymeric Composites

    Significance of Energy Absorbing Layer in GFRP Composite on Flexural Response

    Dynamic Behavior of Fiber-Reinforced-Polymer-Strengthened Grinding Wheels Subjected to Pendulum Impact

    Rectifying LTPD Plans Minimizing Mean Inspection Cost Per Lot of Process Average Quality Using EWMA Statistics

    Evaluation of the Bearing Strength of Single-Shear Bolted Joint Composite Laminate Structures and Research on the Test Fixture

    High Temperature Flexural, Tensile Strength and Oxidation Behavior of Ti3SiC2 Ceramic at 900°C–1300°C in Ambient Air

    Comfort Fitting Using Shape Memory Polymeric Foam

    Investigation of Mechanical Properties of Graphene and Reduced Graphene Oxide Reinforced Epoxy Matrix Composites

    Preparation and Performance Test of Soldered Stators of Ultrasonic Motor

    Characterization of Flexural and Impact Strength of Jute/Almond Hybrid Biocomposite

    Acoustic Instrumentation Setup for Armament Performance Evaluation Applications

    2-DWT and AES: Secure Authentication Management for Polar Iris Templates Using Visual Cryptography

    Flexural Strength Tests of Brittle Materials: Selecting the Number of Specimens and Determining Confidence Limits for Weibull Parameters

    Strength and Fracture Characterization of a Novel Polyurethane Adhesive for the Automotive Industry

    Total Electron Content Anomalies Before Mw 6.0+ Earthquakes in the Seismic Zone of Southwest China Between 2001 and 2013

    Experimental Comparison of Vehicle Vibration Simulation Techniques

    Percolation Effect on the Piezoresistivity of Carbon Nanotube/Cement Composite as a Stress Self-Sensing Material

    Characterization of Non-Crimp Fabric Laminates: Loss of Accuracy Due to Strain Measuring Techniques

    Analysis of Masked Data in a Series System Subjected to Sources of Shocks Under Type I Progressive Hybrid Censoring

    Expanded Polystyrene Geofoam Based Cellular Reinforcement

    Degradation Behavior of BaTiO3 Dielectrics for MLCCs by an Accelerated Life Test With Voltage and Temperature Stress Factors

    Terbium-Doped SrCoO3 as a New Cathode Material for IT–SOFC

    Effect of Low Temperature on Tensile Strength and Mode I Fracture Energy of a Room Temperature Vulcanizing Silicone Adhesive

    Thermal Conductivity and Viscosity of Vegetable Oil–Based Cu, Zn, and Cu–Zn Hybrid Nanofluids

    Exploring Relationships in Surface-Hardness Data Collected With Different Instruments

    An Improved Short-Beam Method for Measuring Multiple Constitutive Properties for Composites

    Experimental Research of Crack Propagation in Polymethyl Methacrylate Material Containing Flaws Under Explosive Stress Waves

    Effect of Concrete Strength Class on Performance of CFRP-Confined Concrete under Compression

    Joint Selective Encryption of CAVLC and Signs of Motion Vectors for H.264/AVC

    On Designing Time-Censored Step-Stress Life Test for Lomax Distribution

    Evaluation of Sports Center Performance Using a Fuzzy Multi-Criteria Decision-Making Model

    Standardization of the End-Notched Flexure Test for Mode II Interlaminar Fracture Toughness Determination of Unidirectional Laminated Composites

    Evaluation of Clustering Parameters in WSN Fields Using Distributed Zone-Based Approach

    Maximum Entropy Analysis to the N Policy M/G/1 Queue with Working Breakdowns

    Understanding the Friction Measured by Standardised Test Methodologies Used to Assess Shoe-Surface Slip Risk

    Context-Aware Services for Mobile Multimedia Application

    A Multi-Criteria Decision Making for Innovation Services Attributes: An Empirical Study of Mobile Banking System

    On Studying Partially Accelerated Life Tests Under Progressive Stress

    Bayesian Estimation of Pareto Distribution Under Failure-Censored Step-Stress Life Test Model

    An Assessment of the Quality-Achieving Reliability of Mechanical Products Based on Information-Poor Theory

    Regression-Based Stiffness Test for Pallets Based on Sample Period Reduction by Trimming

    Slip Prediction Accuracy and Bias of the SATRA STM 603 Whole Shoe Tester

    Determination of Effective Ply-level Properties of Filament Wound Composite Tubes Loaded in Compression

    Improving the Management and Operational Success of the Third Party Logistics Industry in Taiwan: Application of Fuzzy Quality Function Deployment

    Mechanical Properties of Epoxy Resin/PMMA/SiO2 Dental Composites

    Calcination of Intercalated Talcite and Its Effect on the Adsorption of Abietate from Aqueous Solution

    Loading Rate-Dependent Fracture Properties and Electrical Resistance-Based Crack Growth Monitoring of Polycarbonate Reinforced with Carbon Nanotubes Under Tension

    System Reliability of Controllable Repair System With Multiple Imperfect Coverage

    Evaluating the Mediating Effect of Perception of Corporate Social Responsibility Commitment

    Performance of Certified Climbing Helmets During Simulated Climbing Falls

    Interlaminar Shear and Electrical Resistance Responses of Woven-Carbon-Fiber-Reinforced-Polymer Composite Laminates at Cryogenic Temperatures From Cyclic Short Beam Shear Tests

    Impact of Using a Novel Emotional Intelligent Controller for Induction Motor Speed Control

    An Edge-Heating Device for Optical Measurement of Thermochromic Glazing Materials and Recommended Test Procedure

    Design and Development of a Test Fixture and Method for Investigation of Impact During Pre-Stressed Compression

    Evaluating the Operational Efficiency of the Banking Sector in Taiwan: A Two-Stage Data Envelopment Analysis Approach

    Equipment Fragility Due to Shock Response

    Evaluating Smart Living Technology Strategies Using the Analytic Network Process

    Evaluating Convention Destination Images in Australia and Asia

    Application of the Stress-Energy Method for Generating Corrugated Board Cushion Curves

    A New Device for Simulating Athlete-to-Surface Interactions on Natural and Synthetic Turf

    Statistical Analysis of the Stress-Energy Methodology Applied to Cushion Curve Determination

    Study on Glass Defect Inspection Based on Projecting Grating Method

    Improved Digital Image Correlation Method for Eliminating Pixel Shape-Induced Errors in Shear-Strain Calculations

    Compressive Behavior of Square-Cell Titanium Honeycomb

    Measuring Mechanical Properties of the 3D Carbon/Carbon Composite Using Automated Grid Method

    Development of Standard Laboratory Testing Procedures to Evaluate the Performance of Deicers

    Evaluation of Ice-Melting Capacities of Deicing Chemicals

    Solvothermal Synthesis of High Yield CdS Nanowires in Ethylenediamine

    A Study of Process Quality Assessment for Golf Club-Shaft in Leisure Sport Industries

    Evaluation of the Long-Distance Conducted Electrical Weapon XREP®

    Experimental Procedure for the Mechanical Evaluation of Oxide-Carbon Refractories by Strain Measurement

    Experimental Testing and Numerical Evaluation on Freezing for Water Hydraulics Application under Sub-Freezing Ambient Temperature Environment

    Software Reliability Growth Model Based on Half Logistic Distribution

    Testing of Removable Bracket Protection System for Rock Climbing

    Laboratory Investigation into Interactions Among Chemicals Used for Snow and Ice Control

    Evaluation of Predicted Deceleration Values From the Stress-Energy Method Compared to Actual Deceleration Values From the ASTM D1596 Test Method

    Slip Safety Analysis of Differently Surface Processed Dimension Marbles

    A Global Method for the Identification of Failure Modes in Fiberglass Using Acoustic Emission

    Evaluation of Tensile Strength of Woven Carbon/Epoxy Composite Laminates at Cryogenic Temperatures Using the Open Hole Specimens

    Measurements of Thermal Conduction in Partially Saturated Specimens Using the Transient Hot-Disk Technique

    Experimental and Finite Element Analysis of the API RP60 Test

    A Pilot Study on Thermal and Moisture Mapping of the Head-Helmet System Using Micro-Sensor Technology

    Effects of Surface Conditions on Baseball Playing Surface Pace

    Analysis of Fracture in Aluminum Joints Bonded with a Bi-Component Epoxy Adhesive

    Experimental Techniques for Evaluation of Fatigue Characteristics of Laminated Constructions from Composite Materials: Full-Scale Testing of the Helicopter Rotor Blades

    Pore Independent Crack Propagation of Glass-Alumina Functionally Graded Materials

    Industrial Composting of Poly(Lactic Acid) Bottles

    Evaluation of the Stress-Energy Methodology to Predict Transmitted Shock through Expanded Foam Cushions

    Evaluation of Slip Resistant Plates for Roadway Applications

    Effect of Variations in Practice of ASTM D7522 Standard Pull-Off Test for FRP-Concrete Interfaces

    Determination of ε-Caprolactam Concentration in Water and a White Wine Simulant during Simulated Transport and Storage of Lidded Cups

    Implementation of a Fingerprint Recognition System Using LBP Descriptor

    Establishing an Evaluation Model for Emerging Industry Credit Ability for the Banking Sector

    Determination of Physical, Acoustical, Mechanical, and Chemical Properties of Fresh Young Coconut Fruit for Maturity Separation

    Prediction of Cushion Performance Less Than One Inch Thick

    Flexural Strength of Ceramic and Glass Rods

    An IS Quality Measurement Using Gap and Multicriteria Decision-Making Model: A Case Study for Supply Chain Management System

    Mechanical and Light Properties of Mangosteen Fruit as Related to Postharvest Quality

    Constructing a Test Method to Evaluate Stable DVR System

    Strength of a Ceramic Sectored Flexural Test Specimen

    Simplified Presentation of the Stress-Energy Method for General Commercial Use

    Production of Aluminum-Silicon Carbide Composites Using Powder Metallurgy at Sintering Temperatures Above the Aluminum Melting Point

    An Apparatus to Evaluate the Pace of Baseball Field Playing Surfaces

    Testing and Evaluation of Quality Changes of Treated Fresh-Cut Tropical Fruits Packaged in Thermoformed Plastic Containers

    A New Methodology for Whole-Package Microbial Challenge Testing for Medical Device Trays

    A Biaxial Load Cell Design for Simultaneous Measurement of Horizontal and Vertical Spring Forces in Sinuous Spring-Supported Seating

    An Experimentally-Based Analytical Model of the Stress Field in an Iosipescu Composite Test Specimen

    Measurement, Analysis, and Comparison of the Parcel Shipping Shock and Drop Environment of the United States Postal Service with Commercial Carriers

    Short-Beam-Shear Testing of Composite Rings With Variable Cross Section as Representative for Full-scale Delamination

    Test Method to Evaluate Bruising During Impacts to Apples and Compare Cushioning Materials

    Measuring Stress Strain Curves to Large Strains on Sheet Metal

    Characterization and Simulation of the Creep Behavior of P92 Sandwich Structures at 923 K with Loading Transverse to the Intermediate Layer

    Round Robin Test on Normalization Method under Static Loading Condition

    Studying of the Dynamic Behavior of Pile Cushioning Materials in Pile Driving

    Mechanical Principles of a New Two-Way Composite Disk Spring Cap for Pile Driving

    Instrumentation for Determining the Local Damping Capacity in Honeycomb Sandwich Composites

    Tracking the Onset of Damage Mechanism in Ceria-based Solid Oxide Fuel Cells under Simulated Operating Conditions

    Measurement and Analysis of Vibration Levels in Commercial Truck Shipments in Thailand and Its Impact on Packaged Produce

    The Activation Energy of the Static Fatigue (Creep of Steel)

    On the Thick-Adherend Tensile Shear Test of Adhesive Technology—Limitations and Correction Methods

    Hoop Tensile Properties of Ceramic Matrix Composite Cylinders

    Test Foot Contact Time Effects in Pedestrian Slip-Resistance Metrology

    Results of an Interlaboratory Study of the ASTM Standard Test Method for Tensile Properties of Polymer Matrix Composites D 3039

    Knowledge Base System for Human Resource Evaluation in a University Environment

    Combining a Fatigue Model With a Shock Response Spectrum Algorithm

    Measurement and Simulation of Damage to Long Light-Weight Packages in the FedEx 3-Day Saver Parcel Delivery Service

    Measurement and Analysis of Small and Light Weight Parcel Shipping Environment

    Stress Concentration Factor Formulas Useful for Any Dimensions of Shoulder Fillet in a Flat Test Specimen Under Tension and Bending

    Experimental Study of the Strain Rate and Temperature Effects on the Mechanical Behavior of a Magnesium-Silicon Carbide Composite

    The Reliability and Self-Diagnosis of Sensors in a Multisensor Data Fusion Diagnostic System

    Shear Testing of Polymeric Foams

    A Comparison of the Performance Tests Used for Furniture Packaging

    Assessing Testing Bias in Two Walkway-Safety Tribometers

    Ruggedness Experiments for a Calibrated Hot Box Measuring Fenestration Systems Thermal Transmittance

    Finite-Element Analysis of Stress Concentration in ASTM D 638 Tension Specimens

    Compression Loading Applied to Round Double Beam Fracture Specimens. I: Application to Materials with Large Characteristic Lengths

    Stress Concentration Factor Formulas Useful for All Notch Shapes in a Flat Test Specimen Under Tension and Bending

    Ring Hoop Tension Test (RHTT): A Test for Transverse Tensile Properties of Tubular Materials

    Precision and Equivalence of Automatic and Manual Flash Point Apparatus

    Laboratory and Field Evaluation of Piezoelectric Weigh-in-Motion Sensors

    Calibration of Thin Heat Flux Sensors for Building Applications Using ASTM C 1130

    A Critical Appraisal of Fracture Toughness Measurements on AA6061 and an Al2O3-Particle Reinforced AA6061 Alloy for Various Heat Treatments

    A Finite Element Investigation into the Effect of a Skew Insert in a Double-Cantilever Beam Specimen on Calculating Mode I Delamination Fracture Energy of Unidirectional Composites

    Measurement and Analysis of the United Parcel Service Ground Shipping Environment for Large and Heavy Packages

    Evaluation and Adjustments for ASTM D 5656 Standard Test Method for Thick-Adherend Metal Lap-Shear Joints for Determination of the Stress-Strain Behavior of Adhesives in Shear by Tension Loading

    Effects of Fixturing Mass on Dynamic Strain Errors in Structural Fatigue Testing

    Diagnostic Scores for Interlaboratory Study Data

    Porosity and Wear Resistance in Stone Flooring Tiles

    Injuries Due to Traditional and Soft-Core Centered Baseball Impacts: A Review

    Dynamic Shear Modulus and Damping in Iron-Copper and Steel-Based Metal Matrix Composites

    Product/Package Interaction: Effect of Physical, Chemical, and Climatic Environments

    Experimental and Numerical Study of Delamination Growth Induced by a Transverse Crack in Unidirectional Laminates Subjected to Bending Loads

    Displacement Ductility of Steel Members under Axial Tension

    Repeatability and Bias of Two Walkway Safety Tribometers

    Evaluating the Quality of a Mechanical Testing System Using Displacement Field Contours

    Comparison of Returnable Paper and Plastic Corrugated Packaging Trays for the United States Postal Service

    Loss Energy of Composite Materials. Part II: Impact Loading

    The Applicability of ASTM Standard Test Specimens to Fracture and Fatigue Crack Growth of Discontinuous-Fiber Composites

    Results from a Round Robin on a Standard Method for Measurement of Fracture Toughness

    Testing of Sandwich Panels Under Uniform Pressure

    Evaluation of Modified Weibull Distribution for Describing the Strength of Ceramic Fibers and Whiskers with Varying Diameters

    Instantaneous Coefficient of Linear Thermal Expansion—A New Definition

    Measurement of the Fracture Energy of Interfaces in Composites Through Sandwich-Type Chevron-Notched Specimens

    Material Specifications of Advanced Ceramics and Other Issues in the Use of Property Databases with Corrosion Analysis Models

    Repeatability and Reproducibility for Pass/Fail Data

    Effect of Construction Adhesive and Joist Variability on the Deflection Behavior of Light-Frame Wood Floors

    Experimental Assessment of Four Composite Material Shear Test Methods

    International Symposium on Slip Resistance: The Interface of Man, Footwear, and Walking Surfaces

    Comparison of Walkway Safety Tribometers: Part Two

    The Use of the Tortus and the Pendulum with the 4S Rubber for the Assessment of Slip Resistance in the Laboratory and the Field

    Kinematic Methods for Quantifying Loss of Balance While Negotiating a Curved Path on a Slippery Surface

    The Effect of Footwear Midsole Hardness and Thickness on Proprioception and Stability in Older Men

    Analysis of Plowing and Adhesive Effects in the Rolling Ball Tack Method for Pressure Sensitive Adhesives

    Development and Evaluation of a Method to Measure Traction on Turfgrass Surfaces

    High-Resolution Force Plate Analysis of Utilized Slip Resistance in Human Walking

    Required Coefficient of Friction Versus Walking Speed: Potential Influences of Footwear and Walkway Surfaces

    Surface Roughness of Footwear Soling Materials: Relevance to Slip Resistance

    Slip Resistance Characteristics of Footwear Solings Assessed Using the SATRA Friction Tester

    Comparison of R-Curve Methodologies for Ranking the Toughness of Aluminum Alloys

    International Symposium on Slip Resistance: The Interface of Man, Footwear, and Walking Surfaces

    Preliminary Characterization of Thermal Diffusivity for Carbon-Carbon Composites Through Pulsed Video Thermal Imaging

    Measurement and Analysis of the Overnight Small Package Shipping Environment for Federal Express and United Parcel Service

    Robust Design of the Iosipescu Shear Test Specimen for Composites

    Fatigue Strength of Adhesive Bonded Aluminum Joints

    Structure and Outliers in Interlaboratory Studies

    Material Specifications of Advanced Ceramics in Corrosion Studies

    Analysis of the Peel Test: Prediction of Adherend Plastic Dissipation and Extraction of Fracture Energy in Metal-to-Metal Adhesive Joints

    A Compact Testing System for Dynamic Fracture Studies

    Analysis of the Coherence of Published Data on Aluminum Matrix Composites

    A Pneumatic Pressure Bag Testing Machine for Applying a Uniform Load to Panels and Pallets

    Effect of Carbide and Oxide Coating Thickness on Cutting Tool Wear in the Turning Process

    Microcracks: The Hazard Function and Reliability Inspection

    Relationships between Specimen Size, Stress Rate, and Load-Controlled Tensile Properties of AISI 300 Series Stainless Steels at 4 K

    Torsional Fatigue Test for Adhesive Bonded Butt Joints

    TOFSIMS Studies of Cleaning Procedures and Silane Surface Treatments of Steels

    Development of a Novel Specimen Geometry for Fatigue Testing of Fine Wire

    Indentation Characterization of Silicon Nitride

    Determination of Softening Kinetics in a Material by Measuring the Evolution of Hot Flow Stress

    Data Analysis Techniques for Impact Tests of Composite Materials

    An Excitation System for Dynamic Testing of Large Structures

    Relevant Errors Associated with Tension Testing of Metals

    Preparation of Stainless Steel Adherends for Adhesive Bonding

    Introduction to the Sixth International Civil Aviation Security Conference (AVSEC'93)

    Back-Face Strain Compliance and Electrical-Potential Crack Length Calibrations for the Disk-Shaped Compact-Tension DC(T) Specimen

    On the Uncertainties Involved in Quantifying the Fracture Toughness of Al-Li-X Alloys

    Physiologic Challenges Induced by Participation in Ice Hockey—Implications for Training

    Mean Stress Diagrams for Composites Generated Using a Modified Up-and-Down Test Methodology: Part I—Extensive Preliminary Data

    Mean Stress Diagrams for Composites Generated Using a Modified Up-and-Down Test Methodology: Part II—Limited Preliminary Data

    A Mechanical Extensometer for High-Temperature Tensile Testing of Ceramics

    A Fiber Optic Chemical Sensor for Measurement of Groundwater pH

    Density Measurement of Cylindrical Specimens Within a Mold by Gamma-Rays

    Contoured Wood Double Cantilever Beam Specimen for Adhesive Joint Fracture Tests

    Use of a Proposed Test Procedure for Quantifying the Triboelectric Charging Propensity of Packaging Films

    More Rapid Edgewise Crush Test Methods

    Application of Electro-Optic Sensor and Force Transducer on Leak Detection

    Drop Heights Encountered in the United Parcel Service Small Parcel Environment in the United States

    Fracture Testing Wood Adhesives with Composite Cantilever Beams

    High Temperature Tube Burst Test Apparatus

    An Evaluation of Strain Measuring Devices for Ceramic Composites

    Podometrics: A New Methodology for Foot Typing

    Analysis of Gas-Fired Ceramic Radiant Tubes During Transient Heating: Part II—Thermoelastic Stress Analysis

    Experimental Evaluation of a Laboratory Twin-Probe Nuclear Gage for Specimen Density Measurement

    A Cantilever-Type Bend Test Technique for Formability Analysis of Strip/Plate Metals

    The Effect of Handling on the Compression Strength of Corrugated Fiberboard Containers

    Models and Interactions

    Procedure to Evaluate Openings in Children's Products for Head Entrapment Hazards

    Change in Mass of Copper Coupons as a Measure of Severity of Environments in Accelerated Aging Tests for Electrical Contacts

    A Thick Adherend, Instrumented Double-Cantilever-Beam Specimen for Measuring Debonding of Adhesive Joints

    A New Method for Burst Testing of Low Strength Materials

    Fracture of Defect Foam Core Sandwich Beams

    A K1 Calibration for a Modified Single Edge Notched Tension Specimen

    A Method for Uniform Shear Stress-Strain Analysis of Adhesives

    Optimal Stress Amplitude Selection in Estimating Median Fatigue Limits Using Small Samples

    A Technique to Evaluate the Bonding Reactivity of Thermosetting Adhesives

    Morphological Structures in Analysis and Inspection of Hole Quality in Fiber Composites

    Applicability of the Southwell Plot to Shear Deformable Columns

    The Concept of Filament Strength and the Weibull Modulus

    Evaluation of Performance of Three Slip Resistance Testers

    A Comparison of Test Methods for Shear Properties of the Cores of Sandwich Constructions

    Federal Regulation of the Halogenated Solvents

    Development of a Method to Measure Wear on Resilient Flooring—Part II

    CFC 113: A Unique Member of the Halogenated Solvent Family

    Preventing and Coping with Water Pollution

    The Futile Search for the Perfect Shoe Fit

    Fitting a Population of Feet

    Foot Measurement Strategies for Fitting Athletes

    Sensory Attenuation Induced by Modern Athletic Footwear

    Custom Footwear: The Role of Computer-Aided Engineering

    A 1986–1987 Study of Consumer Problems in Shopping for Footwear, with Emphasis on Size and Fit

    Establishing Criteria for a Computerized Vision Inspection of Holes Drilled in Carbon Fiber Composites

    Lateral Collapse Potential of Wood Stringer-Type Pallets

    A Simple, High Precision Biaxial Extensometer for High Temperature Creep Study

    An Experimental Technique for Determining a Measure of Structural Damping

    Stress Analysis of the Cracked-Lap-Shear Specimen: An ASTM Round-Robin

    Compliance Expression for the Middle Cracked Tension Specimen: 2a/W = f(EBV/P)

    Strain Distribution and Temperature Increase During Plane Strain Compression Testing

    Experience with a Digitized Instrumented Impact Testing System

    A Model for Predicting Fracture Toughness of a Cementitious Particulate Composite Molded under Impact Pressure

    A Compression Test for High Strength Ceramics

    A Microcomputer-Based System for the High-Speed Compression Test by the Split Hopkinson Pressure Bar Technique

    Effect of Axial Compression

    Simple Analysis of Gluconate in Cleaner

    Evaluation of the Effect of Contact-Time When Measuring Floor Slip Resistance

    Test Method for Evaluation of Shear Modulus and Modulus of Elasticity of Laminated Anisotropic Composite Materials

    Introduction to Symposium on Explosives Detection for Security Applications

    Algebraic Approximations of Stress-Strain Curves for Kevlar-Reinforced Composites

    A Multistep Shear Test for Bond Strength of Claddings

    The Effectiveness of Passenger Security Screening—an Overview

    Safety Considerations for Photographic Film in the X-Ray Screening of Air Travelers' Luggage

    Cost-Effectiveness of the Passenger Security Screening System

    Training the Security Screening Station Operator

    Passenger Screening Requirements—The View from Europe

    A Constant Amplitude Fatigue Study of an Aluminum Powder Metallurgy Alloy

    Contextual Effects in Category Ratings

    Fractographic Examination in the Scanning Electron Microscope as a Tool in Evaluating Through-Thickness Tension Test Results

    Goodness-of-Fit of the Ramberg-Osgood Analytic Stress-Strain Curve to Tensile Test Data

    Experimental Determination of Lüders Band Parameters from Load-Elongation Data

    High Temperature Cyclic Oxidation Furnace Testing at NASA Lewis Research Center

    Dynamic Effective Young's Modulus of Thin Adhesive Layers in Bonded Joints

    A New Scale of Microtension Test for Polymers

    Development of a Scratch-Test Instrument for Thick Wall Coverings

    Simultaneous Determination of Shear and Young's Moduli in Composites

    Design of a Dynamic Gear Test Rig

    Hydrogen Embrittlement of Zinc Coatings

    Effect of Specimen Shape and Cyclic Loading on Tension Tests of Two Epoxy Resins

    A Procedure for Strain-Controlled High-Cycle Fatigue Testing at Elevated Temperatures

    Effect of Understressing and Coaxing on the Fatigue Limit of a Transverse Butt-Welded Joint

    Statistical Fatigue Failure Analysis

    A Hot Compression Testing Apparatus for the Study of Isothermal Forging

    Application of Accelerated Weathering Test to Glass-Fiber Reinforced Polyester Sheets of Improved Surface Durability

    An Acceptance Plan for Feather and Down Products

    Effect of Clamping Pressure on the Fatigue Strength of Dimpled and Undimpled Loaded Holes

    A New Load-Transmitting Medium to Measure Strength of Brittle Materials

    Computer Simulation of the Tension Test: Effect of Testing Conditions

    Cohesive Bond Strength Prediction for Adhesive Joints

    Powder-Cushion Gripping to Promote Good Alignment in Tensile Testing

    Proportional Biaxial Cyclic Hardening of Annealed Oxygen-Free High-Conductivity Copper

    Low Energy Impact Behavior of Composite Panels

    A Comparison of Methods for Determining the Shear Properties of Glass/Resin Unidirectional Composites

    Fatigue Damage: Stiffness/Strength Comparisons for Composite Materials

    A New Static Compression Fixture for Advanced Composite Materials

    The Effect of Hygrothermal History on Residual Strength of Glass Fiber Reinforced Plastic Laminates

    Enhancement of Compressive Properties of Failed Concrete Cylinders with Polymer Impregnation

    Problems in Standardization of Implantable Stimulation Electrodes

    Static and Impact Properties of Laminated Hybrid Composites

    Static and Impact Behavior of Graphite/Epoxy Composite Laminates Containing Third-Phase Reinforcement Materials

    Comparison of Lap Shear Test Specimens

    Bibliography on Clean Glass

    Processing of Glass Containers for Parenteral Products

    The Removal of Stearic Acid Monolayers from Glass with Organic Solvents

    Cleaning Borosilicate Glass for Biological Application

    Methods for Determining the Strength of Brittle Materials in Compressive Stress States

    Evaluation of Some Factors Affecting Measurements of Slip Resistance of Shoe Sole Materials on Floor Surfaces

    A Comparison of the Elevated Temperature Strength Loss in High Tensile Strength Graphite/Epoxy Composite Laminates Due to Ambient and Accelerated Aging

    Tensile Creep of Angle-Plied Boron/Epoxy Laminates

    Contamination Damage Avoidance Concepts for Propulsion Feed System Components

    Martian Sandstorms and Their Effects on the 1975 Viking Lander System

    Contamination Control During Acceptance Testing of Mariner Class Spacecraft Propulsion Hardware

    Automatic Particle Measurement Systems and Liquid-Handling Techniques for Clean Liquids

    Liquid Metal Embrittlement of 4145 Steel by Lead-Tin and Lead-Antimony Alloys

    Effect of Hydrogen on Iron-Nickel-Cobalt Sealing Alloys

    Some Mechanical Properties of Sintered Fiber Metal Composites

    Specimen Geometry Effects on the Strength of Unidirectional Resin-Matrix Composites

    An Analog Control System for an Inverted Torsion Pendulum

    Determination of Mechanical Design Properties of Materials

    Structural Integrity in Aircraft