You are being redirected because this document is part of your ASTM Compass® subscription.
    This document is part of your ASTM Compass® subscription.

    If you are an ASTM Compass Subscriber and this document is part of your subscription, you can access it for free at ASTM Compass

    The Effect of Liner Component Iron Content on Cladding Corrosion, Hydriding, and PCI Resistance

    Published: 01 January 2005

      Format Pages Price  
    PDF (884K) 23 $25   ADD TO CART
    Complete Source PDF (34M) 918 $195   ADD TO CART

    Cite this document

    X Add email address send
      .RIS For RefWorks, EndNote, ProCite, Reference Manager, Zoteo, and many others.   .DOCX For Microsoft Word


    This paper focuses on the effect of liner component Fe content on cladding corrosion, hydriding and Pellet-Cladding Interaction (PCI) resistance. A multitude of experimental techniques is used to evaluate the various properties. The PCI resistance is evaluated through mandrel testing of unirradiated claddings as well as by ramp tests of pre-irradiated fuel segments in the Studsvik R2 reactor. The results from the mandrel testing indicate that an increase of the iron concentration from 0.05 to 0.21 wt% has a rather small impact on the PCI properties. The ramp data, on the other hand, show a clear decrease in the PCI resistance as the Fe content approaches and exceeds 0.19 wt%. The phenomena involved in secondary degradation are complex, and separate tests are used to evaluate the corrosion resistance in steam as well as the hydriding resistance in pure hydrogen. The corrosion test includes cladding tubes with ZrSn-liner components with iron concentrations from 0.025 to 0.21 wt%. The results show that the corrosion resistance is dramatically increased as the Fe content is increased from 0.025 to 0.05–0.06 wt%, but that a further increase of the Fe concentration only has a minor impact on the corrosion resistance. However, increasing the Fe content from 0.05 to 0.21 wt% increases the hydrogen pick-up rate. The 0.21 wt% Fe liner has a significantly higher density of Secondary Phase Particles (SPPs) as well as slightly larger SPPs than the 0.05 wt% Fe liner. Consequently, it is believed that the SPPs offer sites where hydrogen can easily be absorbed into the Zr-based material, and the frequency of these sites is important for the hydrogen pick-up rate. It is finally concluded that even though the optimization of the Fe concentration in the liner is complex, an iron level regime exists that provides a good balance of resistance against PCI, corrosion, and hydriding.


    Zircaloy, cladding, liner, corrosion, hydriding, pellet-clad interaction, PCI

    Author Information:

    Dahlbäck, M
    Westinghouse Electric Sweden, Västerås,

    Hallstadius, L
    Westinghouse Electric Sweden, Västerås,

    Limbäck, M
    Westinghouse Electric Sweden, Västerås,

    Vesterlund, G
    Westinghouse Electric Sweden, Västerås,

    Andersson, T
    Sandvik Materials Technology, Sandviken,

    Witt, P
    Sandvik Materials Technology, Sandviken,

    Izquierdo, J
    Iberdrola Power Generation, Madrid,

    Remartinez, B
    Iberdrola Power Generation, Madrid,

    Díaz, M
    Institute of Materials Science (CSIC), Madrid,

    Sacedon, JL
    Institute of Materials Science (CSIC), Madrid,

    Alvarez, A-M
    Institute of Materials Science (CSIC), Madrid,

    Engman, U
    Studsvik Nuclear, Studsvik,

    Jakobsson, R
    Studsvik Nuclear, Studsvik,

    Massih, AR
    Quantum Technologies, Uppsala,

    Committee/Subcommittee: B10.02

    DOI: 10.1520/STP37539S