ASTM F3125 / F3125M - 18 Standard Specification for High Strength Structural Bolts and Assemblies, Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum Tensile Strength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile Strength


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    A36/A36M Standard Specification for Carbon Structural Steel

    A354 Standard Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    F436/F436M Standard Specification for Hardened Steel Washers Inch and Metric Dimensions

    F959/F959M Standard Specification for Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners, Inch and Metric Series


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    A194/A194M Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A563M Specification for Carbon and Alloy Steel Nuts (Metric)

    A563 Specification for Carbon and Alloy Steel Nuts

    A563 Specification for Carbon and Alloy Steel Nuts

    A563M Specification for Carbon and Alloy Steel Nuts (Metric)

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    E709 Guide for Magnetic Particle Testing

    E1444/E1444M Practice for Magnetic Particle Testing

    F436/F436M Specification for Hardened Steel Washers Inch and Metric Dimensions

    F606/F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F788 Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F1136/F1136M Specification for Zinc/Aluminum Corrosion Protective Coatings for Fasteners

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1789 Terminology for F16 Mechanical Fasteners

    F1789 Terminology for F16 Mechanical Fasteners

    F1940 Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts

    F2328M Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws, Studs, and Nuts (Metric)

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    F2660 Test Method for Qualifying Coatings for Use on A490 Structural Bolts Relative to Environmental Hydrogen Embrittlement

    F2833 Specification for Corrosion Protective Fastener Coatings with Zinc Rich Base Coat and Aluminum Organic/Inorganic Type

    F3019/F3019M Specification for Chromium Free Zinc-Flake Composite, with or without Integral Lubricant, Corrosion Protective Coatings for Fasteners

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels