ASTM D5630 - 13 Standard Test Method for Ash Content in Plastics


    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    D3935 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material

    D4000 Standard Classification System for Specifying Plastic Materials

    D4066 Standard Classification System for Nylon Injection and Extrusion Materials (PA)

    D4067 Standard Classification System and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods

    D4101 Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials

    D4549 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)

    D4673 Standard Classification System for and Basis for Specification for Acrylonitrile–Butadiene–Styrene (ABS) Plastics and Alloys Molding and Extrusion Materials

    D5138 Standard Classification System and Basis for Specification for Liquid Crystal Polymers Molding and Extrusion Materials (LCP)

    D5205 Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials

    D5336 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material

    D5740 Standard Guide for Writing Material Standards in the Classification Format

    D5990 Standard Classification System and Basis for Polyketone Injection Molding and Extrusion Materials (PK)

    D6339 Standard Classification System for and Basis for Specifications for Syndiotactic Polystyrene Molding and Extrusion (SPS)

    D6394 Standard Classification System for and Basis for Specification for Sulfone Plastics (SP)

    D6778 Standard Classification System and Basis for Specification for Polyoxymethylene Molding and Extrusion Materials (POM)

    D8033 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials

    F451 Standard Specification for Acrylic Bone Cement

    F2306/F2306M Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications

    F2648/F2648M Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications

    F2848 Standard Specification for Medical-Grade Ultra-High-Molecular-Weight Polyethylene Yarns

    F2881/F2881M Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

    F2947/F2947M Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications

    F3390 Standard Specification for 3 through 24 in. Lined Flexible Corrugated Polyethylene Pipe for Land Drainage Applications


    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    D883 Terminology Relating to Plastics

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D2584 Test Method for Ignition Loss of Cured Reinforced Resins

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method