A849 Standard Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe

A979/A979M Standard Specification for Concrete Pavements and Linings Installed in Corrugated Steel Structures in the Field

C39/C39M Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens

C78/C78M Standard Test Method for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)

C94/C94M Standard Specification for Ready-Mixed Concrete

C138/C138M Standard Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

C143/C143M Standard Test Method for Slump of Hydraulic-Cement Concrete

C173/C173M Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method

C215 Standard Test Method for Fundamental Transverse, Longitudinal, and

C231/C231M Standard Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C293/C293M Standard Test Method for Flexural Strength of Concrete (Using Simple Beam With Center-Point Loading)

C330/C330M Standard Specification for Lightweight Aggregates for Structural Concrete

C341/C341M Standard Practice for Preparation and Conditioning of Cast, Drilled, or Sawed Specimens of Hydraulic-Cement Mortar and Concrete Used for Length Change Measurements

C361 Standard Specification for Reinforced Concrete Low-Head Pressure Pipe

C361M Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric)

C469/C469M Standard Test Method for Static Modulus of Elasticity and Poisson’s Ratio of Concrete in Compression

C470/C470M Standard Specification for Molds for Forming Concrete Test Cylinders Vertically

C496/C496M Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens

C497 Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile

C497M Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile (Metric)

C567/C567M Standard Test Method for Determining Density of Structural Lightweight Concrete

C685/C685M Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing

C825 Standard Specification for Precast Concrete Barriers

C858 Standard Specification for Underground Precast Concrete Utility Structures

C915 Standard Specification for Precast Reinforced Concrete Crib Wall Members

C918/C918M Standard Test Method for Measuring Early-Age Compressive Strength and Projecting Later-Age Strength

C935 Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast

C942 Standard Test Method for Compressive Strength of Grouts for Preplaced-Aggregate Concrete in the Laboratory

C1037 Standard Practice for Inspection of Underground Precast Concrete Utility Structures

C1074 Standard Practice for Estimating Concrete Strength by the Maturity Method

C1077 Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

C1089 Standard Specification for Spun Cast Prestressed Concrete Poles

C1116/C1116M Standard Specification for Fiber-Reinforced Concrete

C1176/C1176M Standard Practice for Making Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Table

C1202 Standard Test Method for Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration

C1231/C1231M Standard Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Cylindrical Concrete Specimens

C1399/C1399M Standard Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete

C1433M Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)

C1433 Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers

C1435/C1435M Standard Practice for Molding Roller-Compacted Concrete in Cylinder Molds Using a Vibrating Hammer

C1504 Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains

C1504M Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric)

C1550 Standard Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)

C1556 Standard Test Method for Determining the Apparent Chloride Diffusion Coefficient of Cementitious Mixtures by Bulk Diffusion

C1585 Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes

C1602/C1602M Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

C1609/C1609M Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)

C1670/C1670M Standard Specification for Adhered Manufactured Stone Masonry Veneer Units

C1731 Standard Specification for Concrete Floor Tile

C1757 Standard Test Method for Determination of One-Point, Bulk Water Sorption of Dried Concrete

C1760 Standard Test Method for Bulk Electrical Conductivity of Hardened Concrete

C1768/C1768M Standard Practice for Accelerated Curing of Concrete Cylinders

C1776/C1776M Standard Specification for Wet-Cast Precast Modular Retaining Wall Units

C1792 Standard Test Method for Measurement of Mass Loss versus Time for One-Dimensional Drying of Saturated Concretes

C1804 Standard Specification for Spun Cast Prestressed Concrete Bases for Tapered Steel Lighting Poles

C1837 Standard Specification for Production of Dry Cast Concrete Used for Manufacturing Pipe, Box, and Precast Structures

C1849/C1849M Standard Test Method for Density and Air Content (Pressure Method) of Freshly Mixed Roller-Compacted Concrete

C1856/C1856M Standard Practice for Fabricating and Testing Specimens of Ultra-High Performance Concrete

C1876 Standard Test Method for Bulk Electrical Resistivity or Bulk Conductivity of Concrete

C1890 Standard Test Method for K-slump of Freshly Mixed Concrete

C1894 Standard Guide for Microbially Induced Corrosion of Concrete Products

D4832 Standard Test Method for Preparation and Testing of Controlled Low Strength Material (CLSM) Test Cylinders

D7147 Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers

D7853 Standard Test Method for Hydraulic Pullout Resistance of a Geomembrane with Locking Extensions Embedded in Concrete

D7958/D7958M Standard Test Method for Evaluation of Performance for FRP Composite Bonded to Concrete Substrate using Beam Test

E488/E488M Standard Test Methods for Strength of Anchors in Concrete Elements

F3016/F3016M Standard Test Method for Surrogate Testing of Vehicle Impact Protective Devices at Low Speeds

C125 Terminology Relating to Concrete and Concrete Aggregates

C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

C143/C143M Test Method for Slump of Hydraulic-Cement Concrete

C172/C172M Practice for Sampling Freshly Mixed Concrete

C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method

C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C330/C330M Specification for Lightweight Aggregates for Structural Concrete

C403/C403M Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance

C470/C470M Specification for Molds for Forming Concrete Test Cylinders Vertically

C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes

C617/C617M Practice for Capping Cylindrical Concrete Specimens

C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

C1077 Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

C1611/C1611M Test Method for Slump Flow of Self-Consolidating Concrete

C1758/C1758M Practice for Fabricating Test Specimens with Self-Consolidating Concrete