ASTM C1005 - 19 Standard Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements

    Citing ASTM Standards Citation data is made available by participants in CrossRefs Cited-by Linking service. A comprehensive list of citations to this standard are listed here.

    C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50 mm] Cube Specimens)

    C110 Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone

    C123/C123M Standard Test Method for Lightweight Particles in Aggregate

    C142/C142M Standard Test Method for Clay Lumps and Friable Particles in Aggregates

    C151/C151M Standard Test Method for Autoclave Expansion of Hydraulic Cement

    C185 Standard Test Method for Air Content of Hydraulic Cement Mortar

    C187 Standard Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

    C191 Standard Test Methods for Time of Setting of Hydraulic Cement by Vicat Needle

    C266 Standard Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles

    C348 Standard Test Method for Flexural Strength of Hydraulic-Cement Mortars

    C359 Standard Test Method for Early Stiffening of Hydraulic Cement (Mortar Method)

    C451 Standard Test Method for Early Stiffening of Hydraulic Cement (Paste Method)

    C452 Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate

    C490/C490M Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete

    C513/C513M Standard Test Method for Obtaining and Testing Specimens of Hardened Lightweight Insulating Concrete for Compressive Strength

    C596 Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

    C778 Standard Specification for Standard Sand

    C806 Standard Test Method for Restrained Expansion of Expansive Cement Mortar

    C807 Standard Test Method for Time of Setting of Hydraulic Cement Mortar by Modified Vicat Needle

    C1038/C1038M Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water

    C1222 Standard Practice for Evaluation of Laboratories Testing Hydraulic Cement

    C1240 Standard Specification for Silica Fume Used in Cementitious Mixtures

    C1565 Standard Test Method for Determination of Pack-Set Index of Portland and Blended Hydraulic Cements

    C1585 Standard Test Method for Measurement of Rate of Absorption of Water by Hydraulic-Cement Concretes

    C1679 Standard Practice for Measuring Hydration Kinetics of Hydraulic Cementitious Mixtures Using Isothermal Calorimetry

    C1698 Standard Test Method for Autogenous Strain of Cement Paste and Mortar

    C1708/C1708M Standard Test Methods for Self-leveling Mortars Containing Hydraulic Cements

    C1738/C1738M Standard Practice for High-Shear Mixing of Hydraulic Cement Pastes

    C1753/C1753M Standard Practice for Evaluating Early Hydration of Hydraulic Cementitious Mixtures Using Thermal Measurements

    C1757 Standard Test Method for Determination of One-Point, Bulk Water Sorption of Dried Concrete

    C1792 Standard Test Method for Measurement of Mass Loss versus Time for One-Dimensional Drying of Saturated Concretes

    C1874 Standard Test Method for Measuring Rheological Properties of Cementitious Materials Using Coaxial Rotational Rheometer

    C1891 Standard Test Method for Fineness of Hydraulic Cement by Air Jet Sieving at 45-µm (No. 325)

    D1734 Standard Practice for Making Cementitious Panels for Testing Coatings

    Referenced ASTM Standards The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    C114 Test Methods for Chemical Analysis of Hydraulic Cement

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E617 Specification for Laboratory Weights and Precision Mass Standards