Standard Historical Last Updated: Dec 31, 2010 Track Document
ASTM F606M-07e1

Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets [Metric]

Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets [Metric] F0606M-07E01 ASTM|F0606M-07E01|en-US Standard Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets [Metric] Standard new BOS Vol. 01.09 Committee F16
$ 83.00 In stock

Abstract

These test methods establishes the standard procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners, washers and direct tension indicators, and rivets. For externally threaded fasteners, the mechanical tests describe the procedures for determining the following properties: product hardness; proof load by length measurement (Method 1), yield strength (Method 2), yield strength of austenitic stainless steel and nonferrous materials (Method 2A), and uniform hardness (Method 3); axial tension of full size products such as fasteners and studs; wedge tension of full size products such as fasteners and studs; tension of machined test specimens including yield point (by drop of the beam or halt of the pointer, autographic diagram, and total extension under load methods), yield strength (by offset, and extension under load methods), tensile strength, elongation, and reduction of area; and total extension at fracture. As for internally threaded fasteners including nonheat- and heat-treated nuts, tests are provided for the determination of product hardness, proof load, and cone proof load. Test for determining the surface and core hardnesses are, conversely, described for direct tension indicators, and through-hardened, carburized, stainless steel, and nonferrous washers. And finally, product hardness testing is described for rivets. The test method for determining embrittlement of metallic coated externally threaded fasteners is detailed as well.

Scope

1.1 These test methods cover establishment of procedures for conducting tests to determine the mechanical properties of metric externally and internally threaded fasteners, washers, and rivets.

1.2 Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product shall specify the controlling testing requirements.

1.3 These test methods describe mechanical tests for determining the following properties:

Tests
Section
For Externally Threaded Fasteners:
3
Product Hardness
3.1
Proof Load
3.2.1
Method 1, Length Measurement
3.2.3
Method 2, Yield Strength
3.2.4
Method 3, Uniform Hardness
3.2.5
Axial Tension Testing of Full Size Products
3.4
Wedge Tension Testing of Full Size Products
3.5
Tension Testing of Machined Test Specimens
3.6
Total Extension at Fracture Test
3.7
For Internally Threaded Fasteners:
4
Product Hardness
4.1
Proof Load
4.2
Cone Proof Load Test
4.3
For Washers and Direct Tension Indicators:
5
General Requirements
5.1
Through Hardened Washers
5.2
Carburized Washers
5.3
For Rivets:
6
Product Hardness
6.1
Test for Embrittlement of Metallic Coated Externally Threaded Fasteners

7
Test Method for Determining Decarburization and Carburization8
Test Method for Measuring Compression Loads (All Finishes) on Direct Tension Indicators Covered by Test Method F 959M
Annex A1

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of all of the users of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1—These test methods are the metric companion of Test Methods F 606.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.09
Developed by Subcommittee: F16.01
Pages: 15
DOI: 10.1520/F0606M-07E01
ICS Code: 21.060.01