Standard Historical Last Updated: Dec 13, 2016 Track Document
ASTM F2317/F2317M-16

Standard Specification for Design of Weight-Shift-Control Aircraft

Standard Specification for Design of Weight-Shift-Control Aircraft F2317_F2317M-16 ASTM|F2317_F2317M-16|en-US Standard Specification for Design of Weight-Shift-Control Aircraft Standard new BOS Vol. 15.09 Committee F37
$ 75.00 In stock

Abstract

This specification covers the minimum requirement for designing, testing, and labeling of weight-shift-control aircraft. This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot. Flight requirements are specified for: (1) proof of compliance including hang point and trimming setting; (2) general performance such as (a) stall speed in the landing configuration, (b) stall speed free of control limits, (c) minimum climb performance, (d) flutter, buffeting, and vibration, (e) turning flight and stalls, and (f) maximum sustainable speed in straight and level flight; (3) controllability and maneuverability such as general, longitudinal, and lateral control; and (4) longitudinal stability and pitch testing. Structural requirements specified include: (1) strength requirements, (2) fulfillment of design requirements, (3) safety factors, (4) design airspeeds, (5) flight loads, (6) pilot control loads, (7) ground loads including landing gear shock absorption, and (8) emergency landing loads. Design and construction requirements are specified for: (1) materials, (2) fabrication methods, (3) self-locking nuts, (4) protection of structure, (5) accessibility, (6) setup and breakdown, (7) control system evaluated by operation test, (8) mast (pylon) safety device, (9) cockpit design, and (10) markings and placards. Powerplant requirements including installation, fuel system, oil system, induction system, and fire prevention, as well as equipment requirements such as powerplant instruments, miscellaneous equipment, and lap belts and harnesses, are detailed. Operating limitations such as load distribution limits are also specified.

Scope

1.1 This specification covers the minimum airworthiness standards a manufacturer shall meet in the designing, testing, and labeling of weight-shift-control aircraft.

1.2 This specification covers only weight-shift-control aircraft in which flight control systems do not use hinged surfaces controlled by the pilot.

Note 1: This section is intended to preclude hinged surfaces such as typically found on conventional airplanes such as rudders and elevators. Flexible sail surfaces typically found on weight-shift aircraft are not considered hinged surfaces for the purposes of this specification.

1.3 Weight-shift-control aircraft means a powered aircraft with a framed pivoting wing and a fuselage (trike carriage) controllable only in pitch and roll by the pilot's ability to change the aircraft's center of gravity with respect to the wing. Flight control of the aircraft depends on the wing's ability to flexibly deform rather than the use of control surfaces.

1.4 This specification is organized and numbered in accordance with the bylaws established for Committee F37. The main sections are:

Scope

1

Referenced Documents

2

Terminology

3

Flight Requirements

4

Structural Requirements

5

Design and Construction Requirements

6

Powerplant Requirements

7

Equipment Requirements

8

Operating Limitations

9

Keywords

10

Annex

Annex A1

Appendix

Appendix X1

1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 15.09
Developed by Subcommittee: F37.40
Pages: 10
DOI: 10.1520/F2317_F2317M-16
ICS Code: 49.020