Standard Historical Last Updated: Dec 31, 2010 Track Document
ASTM E1783-96(2009)

Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures

Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures E1783-96R09 ASTM|E1783-96R09|en-US Standard Specification for Preformed Architectural Strip Seals for Buildings and Parking Structures Standard new BOS Vol. 04.11 Committee E06
$ 75.00 In stock

Significance and Use

Architectural strip seals included in this specification shall be those:

Extruded as a membrane,

Extruded as tubular,

With frames,

With flanges mechanically secured,

With flanges chemically secured,

Used in interior or exterior applications, and

Used in any construction of the building.

This specification will give users, producers, building officials, code authorities, and others a basis for verifying material and performance characteristics of representative specimens under common test conditions. This specification will produce data on the following:

The physical properties of the fully cured elastomeric alloy, and

The movement capability in relation to the nominal joint width as defined under Test Method E1399.

This specification compares similar architectural strip seals but is not intended to reflect the system's application. Similar refers to the same type of architectural strip seal within the same subsection under 9.1.

This specification does not provide information on the following:

Durability of the architectural strip seal under actual service conditions, including the effects of cycled temperature on the strip seal;

Loading capability of the system and the effects of a load on the functional parameters established by this specification;

Shear and rotational movements of the specimen;

Any other attributes of the specimen, such as fire resistance, wear resistance, chemical resistance, air infiltration, watertightness, and so forth; and

Note 3—This specification addresses fully cured elastomeric alloys. Test Methods D395, D573, D1052, and D1149 are tests better suited for evaluating thermoset materials.

Testing or compatibility of substrates.

This specification is intended to be used as only one element in the selection of an architectural strip seal for a particular application. It is not intended as an independent pass or fail acceptance procedure. Other standards shall be used in conjunction with this specification to evaluate the importance of other service conditions such as durability, structural loading, and compatibility.

Abstract

This specification covers the physical requirements and movement capabilities of preformed architectural strip seals for use in sealing expansion joints in buildings and parking structures. However, this specification does not provide information on the durability of the architectural strip seals under actual service conditions, loading capability of the system, and the effects of a load on the functional parameters. Material covered by this specification consists of architectural strip seals extruded as a membrane or tubular, with frames, with flanges mechanically or chemically secured, used in interior or exterior application, and used in any construction of the building. The architectural strip seal shall be manufactured from a fully cured elastomeric alloy as a preformed extrusion free of defects such as holes and air bubbles, and with dimensions conforming to the requirements specified. Tests for tensile strength, elongation at break, hardness, ozone resistance, compression set, heat aging, tear resistance, brittleness temperature, and water absorption shall be performed and shall conform to the requirements specified.

Scope

1.1 This specification covers the physical requirements for the fully cured elastomeric alloy and the movement capabilities of preformed architectural compression seals used for sealing expansion joints in buildings and parking structures. The preformed architectural strip seal is an elastomeric extrusion. This extrusion is either a membrane or tubular having an internal baffle system produced continuously and longitudinally throughout the material. These extrusions are secured in or over a joint by locking rails or an end dam nosing material. The architectural strip seal is compressed and expanded by this mechanical or chemical attachment.

Note 1—Movement capability is defined in Test Method E1399.

1.2 This specification covers all colors of architectural strip seals.

Note 2—The products described in this specification are manufactured from thermoplastic elastomers defined as fully cured elastomeric alloys in Test Method D5048.

1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 04.11
Developed by Subcommittee: E06.21
Pages: 5
DOI: 10.1520/E1783-96R09
ICS Code: 91.100.50; 93.080.20