SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|9||$60.00||  ADD TO CART|
1.1 This guide is focused on the general procedures necessary to conduct neutron or neutron porosity (hereafter referred to as neutron) logging of boreholes, wells, access tubes, caissons, or shafts (hereafter referred to as boreholes) as commonly applied to geologic, engineering, groundwater and environmental (hereafter referred to as geotechnical) investigations. Neutron soil moisture measurements made using neutron moisture gauges, are excluded. Neutron logging for minerals or petroleum applications is excluded, along with neutron activation logs where gamma spectral detectors are used to characterize the induced gamma activity of minerals exposed to neutron radiation.
1.2 This guide defines a neutron log as a record of the rate at which thermal and epithermal neutrons are scattered back to one or more detectors located on a probe adjacent to a neutron source.
1.2.1 Induction logs are treated quantitatively and should be interpreted with other logs and data whenever possible.
1.2.2 Neutron logs are commonly used to: (1) delineate lithology, and (2) indicate the water-filled porosity of formations (see Fig. 1).
1.3 This guide is restricted to neutron logging with nuclear counters consisting of scintillation detectors (crystals coupled with photomultiplier tubes), or to He3-tube detectors with or without Cd foil covers or coatings to exclude thermalized neutrons.
1.4 This guide provides an overview of neutron logging including: (1) general procedures; (2) specific documentation; (3) calibration and standardization, and (4) log quality and interpretation.
1.5 To obtain additional information on neutron logs see References section in this guide.
1.6 This guide is to be used in conjunction with Standard Guide D5753.
1.7 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This guide should not be used as a sole criterion for neutron logging and does not replace education, experience, and professional judgment. Neutron logging procedures should be adapted to meet the needs of a range of applications and stated in general terms so that flexibility or innovation are not suppressed. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged without consideration of a project's many unique aspects. The word standard in the title of this document means that the document has been approved through the ASTM consensus process.
1.8 The geotechnical industry uses English or SI units. The neutron log is typically recorded in units of counts per second (cps) or in percent porosity.
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use. The use of radioactive sources in neutron logging introduces significant safety issues related to the transportation and handling of neutron sources, and in procedures to insure that sources are not lost or damaged during logging. There are different restrictions on the use of radioactive sources in logging in different states, and the Nuclear Regulatory Agency (NRC) maintains strict rules and regulations for the licensing of personnel authorized to conduct nuclear source logging.
A–Single detector epithermal neutron log plotted in counts per second.
B–Dual-detector neutron log calibrated in limestone porosity units.
C–Gamma log showing maximum and minimum values used as endpoints for the gamma activity scale.
D–Dual detector neutron log plotted in porosity units corrected for the non-effective porosity of clay minerals using the equation:
|=||corrected neutron log,|
|=||original neutron log,|
|=||computed shale fraction based upon the gamma log position between the endpoints of 10 and 120 cps, and|
|=||estimate of shale non-effective porosity of about 40 % picked from intervals on the log where Φsh = 1.0.|
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D420 Guide to Site Characterization for Engineering Design and Construction Purposes
D653 Terminology Relating to Soil, Rock, and Contained Fluids
D5088 Practice for Decontamination of Field Equipment Used at Waste Sites
D5608 Practices for Decontamination of Field Equipment Used at Low Level Radioactive Waste Sites
D5730 Guide for Site Characterization for Environmental Purposes With Emphasis on Soil, Rock, the Vadose Zone and Ground Water
D5753 Guide for Planning and Conducting Borehole Geophysical Logging
D6167 Guide for Conducting Borehole Geophysical Logging: Mechanical Caliper
D6235 Practice for Expedited Site Characterization of Vadose Zone and Groundwater Contamination at Hazardous Waste Contaminated Sites
D6274 Guide for Conducting Borehole Geophysical Logging - Gamma
D6429 Guide for Selecting Surface Geophysical Methods
ICS Number Code 93.020 (Earthworks. Excavations. Foundation construction. Underground works)
UNSPSC Code 81151902(Geophysical exploration)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D6727-01(2007), Standard Guide for Conducting Borehole Geophysical Logging - Neutron, ASTM International, West Conshohocken, PA, 2007, www.astm.orgBack to Top