ASTM D5874-02(2007)

    Standard Test Method for Determination of the Impact Value (IV) of a Soil


      Format Pages Price  
    PDF 9 $60.00   ADD TO CART

    Active (view current version of standard)

    Other Historical Standards

    Work Item(s) - proposed revisions of this standard

    ASTM License Agreement

    More D18.08 Standards Related Products


    1. Scope

    1.1 This test method covers the determination of the Impact Value (IV) of a soil either in the field or a test mold.

    1.2 The standard test method, using a 4.5 kg (10 lbm) hammer, is suitable for, but not limited to, evaluating the strength of an unsaturated compacted fill, in particular pavement materials, soils, and soil-aggregates having maximum particle sizes less than 37.5 mm (1.5 in.).

    1.3 By using a lighter 0.5 kg (1.1 lbm) hammer, this test method is applicable for evaluating lower strength soils such as fine grained cohesion less, highly organic, saturated, or highly plastic soils having a maximum particle size less than 9.5 mm (0.375 in.).

    1.4 By performing laboratory test correlations for a particular soil using the 4.5 kg (10 lbm) hammer, IV may be correlated with an unsoaked California Bearing Ratio (CBR) or may be used to infer percentage compaction.

    1.5 The values stated SI are to be regarded as the standard. The values stated in parentheses are given for information only.

    1.6 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026. The method used to specify how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other uses or both. How one applies the results obtained using this standard is beyond its scope.

    1.7 This standard may involve hazardous materials, operations, and equipment This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1The equipment and procedures contained in this test method are similar to those developed by B. Clegg in the 1970s at the University of Western Australia, Nedlands, Australia. Impact Value is also commonly known as Clegg Impact Value (CIV).


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12 400 ft-lbf/ft3 (600 kN-m/m3))

    D1556 Test Method for Density and Unit Weight of Soil in Place by Sand-Cone Method

    D1557 Test Methods for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))

    D1883 Test Method for California Bearing Ratio (CBR) of Laboratory-Compacted Soils

    D2167 Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method

    D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    D2937 Test Method for Density of Soil in Place by the Drive-Cylinder Method

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4643 Test Method for Determination of Water (Moisture) Content of Soil by Microwave Oven Heating

    D4959 Test Method for Determination of Water (Moisture) Content of Soil By Direct Heating

    D6026 Practice for Using Significant Digits in Geotechnical Data

    D6938 Test Methods for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)


    ICS Code

    ICS Number Code 13.080.20 (Physical properties of soil)

    UNSPSC Code

    UNSPSC Code 11111501(Soil)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D5874-02R07

    Citation Format

    ASTM D5874-02(2007), Standard Test Method for Determination of the Impact Value (IV) of a Soil, ASTM International, West Conshohocken, PA, 2007, www.astm.org

    Back to Top