ASTM D5784/D5784M-13

    Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices


      Format Pages Price  
    PDF 7 $60.00   ADD TO CART


    1. Scope

    1.1 This guide covers how hollow-stem auger-drilling systems may be used for geoenvironmental exploration and installation of subsurface water-quality monitoring devices.

    1.2 Hollow-stem auger drilling for geoenvironmental exploration and monitoring device installations often involves safety planning, administration, and documentation. This guide does not purport to specifically address exploration and site safety.

    Note 1This guide does not include considerations for geotechnical site characterizations that are addressed in a separate guide.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.5 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D1586 Test Method for Standard Penetration Test (SPT) and Split-Barrel Sampling of Soils

    D1587 Practice for Thin-Walled Tube Sampling of Fine-Grained Soils for Geotechnical Purposes

    D2113 Practice for Rock Core Drilling and Sampling of Rock for Site Exploration

    D2487 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)

    D2488 Practice for Description and Identification of Soils (Visual-Manual Procedures)

    D3550 Practice for Thick Wall, Ring-Lined, Split Barrel, Drive Sampling of Soils

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4428/D4428M Test Methods for Crosshole Seismic Testing

    D5088 Practice for Decontamination of Field Equipment Used at Waste Sites

    D5092 Practice for Design and Installation of Groundwater Monitoring Wells

    D5434 Guide for Field Logging of Subsurface Explorations of Soil and Rock

    D5521 Guide for Development of Groundwater Monitoring Wells in Granular Aquifers

    D6151 Practice for Using Hollow-Stem Augers for Geotechnical Exploration and Soil Sampling


    ICS Code

    ICS Number Code 13.060.10 (Water of natural resources)

    UNSPSC Code

    UNSPSC Code 81151902(Geophysical exploration)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D5784_D5784M-13

    Citation Format

    ASTM D5784 / D5784M-13, Standard Guide for Use of Hollow-Stem Augers for Geoenvironmental Exploration and the Installation of Subsurface Water-Quality Monitoring Devices, ASTM International, West Conshohocken, PA, 2013, www.astm.org

    Back to Top