ASTM D5195-08

    Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods


      Format Pages Price  
    PDF 5 $60.00   ADD TO CART

    Active (view current version of standard)

    Other Historical Standards

    Work Item(s) - proposed revisions of this standard

    ASTM License Agreement

    More D18.08 Standards Related Products


    1. Scope

    1.1 This test method covers the calculation of the density of soil and rock by the attenuation of gamma radiation, where the gamma source and the gamma detector are placed at the desired depth in a bored hole lined by an access tube.

    1.1.1 For limitations see Section 5 on Interference.

    1.2 The density, in mass per unit volume of the material under test, is calculated by comparing the detected rate of gamma radiation with previously established calibration data (see Annex A1).

    1.3 A precision statement has not been developed for this standard at this time. Therefore, this standard should not be used for acceptance or rejection of a material for purchasign purposes unless correlated to other accepted ASTM standards.

    1.4 The values stated in SI units are regarded as the standard. The inch-pound units given in parentheses are for information only and may be approximate.

    1.5 All observed and calculated values shall conform to the guide for significant digits and rounding established in Practice D6026.

    1.5.1 The procedures used to specify how data are collected, recorded, and calculated in this standard are regarded as the industry standard. In addition, they are representative of the significant digits that should generally be retained. The procedures used do not consider material variation, purpose for obtaining the data, special purpose studies, or any considerations for the users objectives; and it is common practice to increase or reduce significant digits of reported data to be commensurate with these considerations. It is beyond the scope of this standard to consider significant digits used in analysis methods for engineering design.

    1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7, Hazards.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D1452 Practice for Soil Exploration and Sampling by Auger Borings

    D1587 Practice for Thin-Walled Tube Sampling of Soils for Geotechnical Purposes

    D2113 Practice for Rock Core Drilling and Sampling of Rock for Site Investigation

    D2216 Test Methods for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass

    D2937 Test Method for Density of Soil in Place by the Drive-Cylinder Method

    D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction

    D4428/D4428M Test Methods for Crosshole Seismic Testing

    D5220 Test Method for Water Mass per Unit Volume of Soil and Rock In-Place by the Neutron Depth Probe Method

    D6026 Practice for Using Significant Digits in Geotechnical Data

    D6938 Test Method for In-Place Density and Water Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth)


    ICS Code

    ICS Number Code 93.020 (Earth works. Excavations. Foundation construction. Underground works)

    UNSPSC Code

    UNSPSC Code 11111501(Soil); 41114000(Rock and strata measuring equipment)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D5195-08

    Citation Format

    ASTM D5195-08, Standard Test Method for Density of Soil and Rock In-Place at Depths Below Surface by Nuclear Methods, ASTM International, West Conshohocken, PA, 2008, www.astm.org

    Back to Top