ASTM D2829-04

    Standard Practice for Sampling and Analysis of Built-Up Roofs


      Format Pages Price  
    PDF 5 $60.00   ADD TO CART


    1. Scope

    1.1 This practice is a guide for removing test specimens from built-up roofing systems in the field and for determining the approximate quantities of the components of that specimen (Note 0). Components determined may be:

    1.1.1 Insulation components when they are part of the roof membrane system,

    1.1.2 Plies of roofing felt,

    1.1.3 Interply layers of bituminous material,

    1.1.4 Top coating, and

    1.1.5 Surfacing.

    Note 1—This procedure is for the investigation of existing roofs and is not intended for new construction inspection.

    1.2 This practice is applicable to 914-mm (36-in.) wide felt rolls only and does not apply to metric-sized (that is, 1000-mm (393/8-in.) wide) felt rolls.

    1.3 The values stated in SI (metric) units are to be regarded as standard.

    This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary information, see 6.3.2.1.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D226 Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing

    D227 Specification for Coal-Tar-Saturated Organic Felt Used in Roofing and Waterproofing

    D249 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules

    D250 Standard Specification for Asphalt-Saturated Asbestos Felt Used in Roofing and Waterproofing

    D371 Specification for Asphalt Roll Roofing (Organic Felt) Surfaced with Mineral Granules; Wide Selvage

    D1079 Terminology Relating to Roofing and Waterproofing

    D2178 Specification for Asphalt Glass Felt Used in Roofing and Waterproofing

    D2626 Specification for Asphalt-Saturated and Coated Organic Felt Base Sheet Used in Roofing

    D3158 Specification for Asphalt Saturated and Coated Organic Felt Used in Roofing

    D3617 Practice for Sampling and Analysis of Built-Up Roof Systems During Application

    D3672 Standard Specification for Venting Asphalt-Saturated and Coated Inorganic Felt Base Sheet Used in Roofing

    D3909 Specification for Asphalt Roll Roofing (Glass Felt) Surfaced With Mineral Granules

    D4601 Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing

    D4897 Specification for Asphalt-Coated Glass-Fiber Venting Base Sheet Used in Roofing

    D4990 Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30151500(Roofing materials); 30121500(Bituminous derivatives)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D2829-04

    Citation Format

    ASTM D2829-04, Standard Practice for Sampling and Analysis of Built-Up Roofs, ASTM International, West Conshohocken, PA, 2004, www.astm.org

    Back to Top