SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|5||$60.00||  ADD TO CART|
1.1 This specification covers the classification of polyethylene film and sheeting up to 0.3 mm (0.012 in.) in thickness, inclusive. The film or sheeting may contain additives for the improvement of the surface properties, pigments, or stabilizers, or combinations thereof.
1.2 The values stated in SI units are to be regarded as standard. The values given in brackets are for information only.
1.3 The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This specification allows for the use of recycled polyethylene film or resin as feedstock, in whole or in part, as long as all the requirements as governed by the producer and end user are also met (see Note 1).
Note 1—Guide D7209 describes terminology and definitions related to recycled plastics.
Note 2—There is no known ISO equivalent to this specification.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D618 Practice for Conditioning Plastics for Testing
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D882 Test Method for Tensile Properties of Thin Plastic Sheeting
D883 Terminology Relating to Plastics
D1003 Test Method for Haze and Luminous Transmittance of Transparent Plastics
D1004 Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting
D1434 Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1709 Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method
D1746 Test Method for Transparency of Plastic Sheeting
D1894 Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
D1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
D1938 Test Method for Tear-Propagation Resistance (Trouser Tear) of Plastic Film and Thin Sheeting by a Single-Tear Method
D2457 Test Method for Specular Gloss of Plastic Films and Solid Plastics
D2578 Test Method for Wetting Tension of Polyethylene and Polypropylene Films
D2839 Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
D3892 Practice for Packaging/Packing of Plastics
D4321 Test Method for Package Yield of Plastic Film
D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials
D5947 Test Methods for Physical Dimensions of Solid Plastics Specimens
D6988 Guide for Determination of Thickness of Plastic Film Test Specimens
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
E96/E96M Test Methods for Water Vapor Transmission of Materials
F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
ICS Number Code 83.140.10 (Films and sheets)
UNSPSC Code 13111201(Polyethylene films); 30265802(Plastic sheet)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D2103-10, Standard Specification for Polyethylene Film and Sheeting, ASTM International, West Conshohocken, PA, 2010, www.astm.orgBack to Top