SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|38||$86.00||  ADD TO CART|
1.1 This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
Note 1--This classification system may serve many of the needs of other industries in much the same manner as SAE numbered steels. It must be remembered, however, that this system is subject to revision when required by automotive needs. It is recommended that the latest revision always be used.
1.2 This classification system is based on the premise that the properties of all rubber products can be arranged into characteristic material designations. These designations are determined by types, based on resistance to heat aging, and classes, based on resistance to swelling in oil. Basic levels are thus established which, together with values describing additional requirements, permit complete description of the quality of all elastomeric materials.
1.3 In all cases where the provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence.
Note 2--When the rubber product is to be used for purposes where the requirements are too specific to be completely prescribed by this classification system, it is necessary for the purchaser to consult the supplier in advance, to establish the appropriate properties, test methods, and specification test limits.
1.4 The values stated in SI units are to be regarded as the standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D395 Test Methods for Rubber PropertyCompression Set
D412 Test Methods for Vulcanized Rubber and Thermoplastic ElastomersTension
D429 Test Methods for Rubber Property--Adhesion to Rigid Substrates
D430 Test Methods for Rubber Deterioration--Dynamic Fatigue
D471 Test Method for Rubber PropertyEffect of Liquids
D573 Test Method for RubberDeterioration in an Air Oven
D575 Test Methods for Rubber Properties in Compression
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D865 Test Method for Rubber--Deterioration by Heating in Air (Test Tube Enclosure)
D925 Test Methods for Rubber Property--Staining of Surfaces (Contact, Migration, and Diffusion)
D945 Test Methods for Rubber Properties in Compression or Shear (Mechanical Oscillograph)
D1053 Test Methods for Rubber Property--Stiffening at Low Temperatures: Flexible Polymers and Coated Fabrics
D1149 Test Methods for Rubber DeteriorationCracking in an Ozone Controlled Environment
D1171 Test Method for Rubber DeteriorationSurface Ozone Cracking Outdoors (Triangular Specimens)
D1329 Test Method for Evaluating Rubber PropertyRetraction at Lower Temperatures (TR Test)
D1349 Practice for Rubber--Standard Conditions for Testing
D1418 Practice for Rubber and Rubber LaticesNomenclature
D2137 Test Methods for Rubber PropertyBrittleness Point of Flexible Polymers and Coated Fabrics
D2240 Test Method for Rubber PropertyDurometer Hardness
D3183 Practice for RubberPreparation of Pieces for Test Purposes from Products
D5964 Practice for Rubber IRM 901, IRM 902, and IRM 903 Replacement Oils for ASTM No. 1, ASTM No. 2, ASTM No. 3 Oils, and IRM 905 formerly ASTM No. 5 Oil
SAE StandardSAE J2979 Test Method for Vulcanized Rubber and Thermoplastic Elastomer Determination of Compressive Stress Relaxation (CSR) Response
ICS Number Code 83.060 (Rubber); 83.160.01 (Tyres in general)
UNSPSC Code 13101500(Natural rubber); 13101600(Processed and synthetic rubber)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D2000-01, Standard Classification System for Rubber Products in Automotive Applications, ASTM International, West Conshohocken, PA, 2001, www.astm.orgBack to Top