SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|8||$60.00||  ADD TO CART|
1.1 This specification provides for the identification of polyethylene plastics extrusion materials for wire and cable in such a manner that the seller and the purchaser can agree on the acceptability of different commercial lots or shipments. The tests involved in this specification are intended to provide information for identifying materials according to the types, classes, categories, and grades covered. It is not the function of this specification to provide specific engineering data for design purposes.
1.2 This specification does not allow for the use of recycled plastics (see Note 3).
1.3 The values stated in SI units are to be regarded as the standard.
1.4 The following safety hazards caveat pertains only to the test method portion, Section 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note 1—No ISO equivalent.
Note 2—This standard has undergone major revision from the reapproval of 1989 and now covers only polyethylene for wire and cable applications. For information regarding molding and extrusion materials, see Specification D 4976. For information regarding plastic pipe materials, see Specification D 3350.
Note 3—See Guide D 5033 for information and definitions related to recycled plastics.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D257 Test Methods for DC Resistance or Conductance of Insulating Materials
D618 Practice for Conditioning Plastics for Testing
D638 Test Method for Tensile Properties of Plastics
D746 Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer
D1505 Test Method for Density of Plastics by the Density-Gradient Technique
D1531 Test Methods for Relative Permittivity (Dielectric Constant) and Dissipation Factor by Fluid Displacement Procedures
D1603 Test Method for Carbon Black Content in Olefin Plastics
D1693 Test Method for Environmental Stress-Cracking of Ethylene Plastics
D2565 Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications
D2633 Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable
D2839 Practice for Use of a Melt Index Strand for Determining Density of Polyethylene
D2951 Test Method for Resistance of Types III and IV Polyethylene Plastics to Thermal Stress-Cracking
D3182 Practice for RubberMaterials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
D3349 Test Method for Absorption Coefficient of Ethylene Polymer Material Pigmented with Carbon Black
D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials
D3636 Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials
D3892 Practice for Packaging/Packing of Plastics
D4329 Practice for Fluorescent Ultraviolet (UV) Lamp Apparatus Exposure of Plastics
D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials
D6360 Practice for Enclosed Carbon-Arc Exposures of Plastics
D7209 Guide for Waste Reduction, Resource Recovery, and Use of Recycled Polymeric Materials and Products
E1131 Test Method for Compositional Analysis by Thermogravimetry
G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources
G153 Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
G154 Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials
G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
ICS Number Code 83.140.99 (Other rubber and plastic products)
UNSPSC Code 13111016(Polyethylene)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D1248-00a, Standard Specification for Polyethylene Plastics Extrusion Materials For Wire and Cable, ASTM International, West Conshohocken, PA, 2002, www.astm.orgBack to Top