ASTM C1172-96e1

    Standard Specification for Laminated Architectural Flat Glass

      Format Pages Price  
    PDF 5 $55.20   ADD TO CART

    1. Scope

    1.1 This specification covers the quality requirements for cut sizes of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building glazing.

    1.2 Depending on the number, thickness and treatment of plies, and the number and thickness of interlayers, the glass shall be laminated safety glass, laminated security glass or laminated bullet resistant glass.

    1.3 The dimensional values, except thickness designations, stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.4 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C162 Terminology of Glass and Glass Products

    C1036 Specification for Flat Glass

    C1048 Specification for Heat-Strengthened and Fully Tempered Flat Glass

    C1376 Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass

    C1422 Specification for Chemically Strengthened Flat Glass

    C1503 Specification for Silvered Flat Glass Mirror

    E308 Practice for Computing the Colors of Objects by Using the CIE System

    E413 Classification for Rating Sound Insulation

    E903 Test Method for Solar Absorptance, Reflectance, and Transmittance of Materials Using Integrating Spheres

    E1332 Classification for Rating Outdoor-Indoor Sound Attenuation

    E1886 Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials

    E1996 Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes

    E2395 Specification for Voluntary Security Performance of Window and Door Assemblies with and without Glazing Impact

    F1233 Test Method for Security Glazing Materials And Systems

    F1642 Test Method for Glazing and Glazing Systems Subject to Airblast Loadings

    F1915 Test Methods for Glazing for Detention Facilities

    F3006 Specification for Ball Drop Impact Resistance of Laminated Architectural Flat Glazing

    F3007 Test Method for Ball Drop Impact Resistance of Laminated Architectural Flat Glass

    ANSI Standard

    Z97.1 Safety Glazing Materials Used in Buildings--Safety Performance Specifications and Methods of Tests Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036,

    Federal Document

    CPSC 16CFR1201 Consumer Product Safety Commission Safety Standard for Architectural Glazing Materials

    National Institute of Justice (NIJ) Standard

    NIJ 0108.1 Ballistic Resistant Protective Materials

    UL Standards

    UL 752 Standard for Bullet Resisting Materials

    UL 972 Standard for Burglary Resisting Glazing Materials

    ICS Code

    ICS Number Code 81.040.20 (Glass in building)

    UNSPSC Code

    UNSPSC Code 30171700(Glass products)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/C1172-96E01

    Citation Format

    ASTM C1172-96e1, Standard Specification for Laminated Architectural Flat Glass, ASTM International, West Conshohocken, PA, 1996,

    Back to Top