ASTM B839-94

    Standard Test Method for Residual Embrittlement in Metallic Coated, Externally Threaded Articles, Fasteners, and Rod-Inclined Wedge Method

      Format Pages Price  
    PDF 4 $49.20   ADD TO CART

    1. Scope

    1.1 This test method covers the determination of, on a statistical basis, the probability of the existence of hydrogen embrittlement or degradation in:

    1.1.1 A batch of barrel electroplated, autocatalytic plated, phosphated, or chemically processed threaded articles or fasteners and

    1.1.2 A batch of rack plated threaded articles, fasteners, or rod.

    1.2 Industrial practice for threaded articles, fasteners, and rod has evolved three graduated levels of test exposure to ensure reduced risk of hydrogen embrittlement (see Section 3). These levels have evolved from commercial applications having varying levels of criticality. In essence, they represent the confidence level that is required. They also represent the time that finished goods are held before they can be shipped and used. This time equates to additional cost to the manufacturer that may of necessity be added to the cost of the finished goods.

    1.3 This test method is applicable to threaded articles, fasteners, and rod made from steel with [>=]1000 MPa (with corresponding hardness values of 300 HV10kg f , 303 HB, or 31 HRc) or surface hardened threaded articles, fasteners, or rod.

    1.4 This test method shall be carried out after hydrogen embrittlement relief heat treatment in accordance with the requirements of Specification B850. It may also be used for assessing differences in processing solutions, conditions, and techniques. This test method has two main functions: first, when used with a statistical sampling plan it can be used for lot acceptance or rejection, and second, it can be used as a control test to determine the effectiveness of the various processing steps including pre- and post-baking treatments to reduce the mobile hydrogen in the articles, fasteners, or rod. While this test method is capable of indicating those items that are embrittled to the extent defined in Section 3, it does not guarantee complete freedom from embrittlement.

    1.5 This test method does not relieve the processor from imposing and monitoring suitable process control.

    1.6 This test method has been coordinated with ISO/DIS 10587 and is technically equivalent.

    Note 1-Great care should be taken when applying this test method. The heads of embrittled articles, fasteners, or rod may suddenly break off and become flying projectiles capable of causing blindness or other serious injury. This hazard can occur as long as 200 h after the test has started. Hence, shields or other apparatus should be provided to avoid such injury. Note 2-The use of inhibitors in acid pickling baths does not necessarily guarantee avoidance of hydrogen embrittlement.

    1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B602 Test Method for Attribute Sampling of Metallic and Inorganic Coatings

    B697 Guide for Selection of Sampling Plans for Inspection of Electrodeposited Metallic and Inorganic Coatings

    B850 Guide for Post-Coating Treatments of Steel for Reducing the Risk of Hydrogen Embrittlement

    F436 Specification for Hardened Steel Washers

    F1940 Test Method for Process Control Verification to Prevent Hydrogen Embrittlement in Plated or Coated Fasteners

    UNSPSC Code

    UNSPSC Code 31162400(Miscellaneous fasteners)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/B0839-94

    Citation Format

    ASTM B839-94, Standard Test Method for Residual Embrittlement in Metallic Coated, Externally Threaded Articles, Fasteners, and Rod-Inclined Wedge Method, ASTM International, West Conshohocken, PA, 1994,

    Back to Top