SUPERSEDED (click for standard)
| ||Format||Pages||Price|| |
|9||$55.20||  ADD TO CART|
1.1 This specification covers selected aluminum, aluminum-alloy and aluminum clad steel cable shielding stock, both uncoated and coated, for applications such as electrostatic or electromagnetic shielding for insulated power, control, instrumentation and communication cables (including coaxial cable).Note 1-See B694, Specification for Copper, Copper Alloy, and Copper-Clad Stainless Steel Sheet and Strip for Electrical Cable Shielding for related standards for copper-based shielding materials.
1.2 The materials covered are the following:Type of Material A Coating Aluminum 1060 none Aluminum 1100 none Aluminum 1145 none Aluminum 1235 none Alloy 3003 none Aluminum 1060 polyolefin Aluminum 1100 polyolefin Aluminum 1145 polyolefin Aluminum 1235 polyolefin Alloy 3003 polyolefin Aluminum 1060 vinyl resin Aluminum 1100 vinyl resin Aluminum 1145 vinyl resin Aluminum 1235 vinyl resin Alloy 3003 vinyl resin Aluminum Clad Steel B none Aluminum Clad Steel B polyolefin A Aluminum designations are in accordance with ANSI H35.1. The equivalent Unified Numbering System alloy designations are those shown preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E 527. B Cladding ratio must be specified (see 5.4).
1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.5 The following precautionary caveat pertains only to the test method portion, Section 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A568/A568M Specification for Steel, Sheet, Carbon, Structural, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
B193 Test Method for Resistivity of Electrical Conductor Materials
B557 Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products
B694 Specification for Copper, Copper-Alloy, Copper-Clad Bronze (CCB), Copper-Clad Stainless Steel (CCS), and Copper-Clad Alloy Steel (CAS) Sheet and Strip for Electrical Cable Shielding
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607 Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spectrochemical Analysis
E1251 Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
American National StandardsB46.1 Surface Texture Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
ICS Number Code 77.150.10 (Aluminium products)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM B736-00, Standard Specification for Aluminum, Aluminum Alloy and Aluminum-Clad Steel Cable Shielding Stock, ASTM International, West Conshohocken, PA, 2000, www.astm.orgBack to Top