Standard Historical Last Updated: Nov 06, 2015 Track Document
ASTM B474-03(2009)

Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe

Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe B0474-03R09 ASTM|B0474-03R09|en-US Standard Specification for Electric Fusion Welded Nickel and Nickel Alloy Pipe Standard new BOS Vol. 02.04 Committee B02
$ 75.00 In stock

Abstract

This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service. The pipes are designated into five classes namely Class 1, Class 2, Class 3, Class 4 and Class 5, according to how they are to be welded. The joints shall be full penetration double-welded or single-welded butt joints employing fusion welding processes. The furnished pipe shall undergo heat treatment and a chemical analysis shall be employed for both plate and weld. Each pipe shall be subjected to transverse tension test, transverse guided weld bend test and hydrostatic pressure test.

Scope

1.1 This specification covers electric fusion welded pipe suitable for high-temperature or corrosive service as listed in Table 1. (Although no restrictions are placed on the sizes of pipe that may be furnished under this specification, commercial practice is commonly limited to sizes not less than 8 in. (203 mm) nominal diameter.)

1.2 Five classes of pipe are covered as follows:

1.2.1 Class 1Pipe shall be double welded by processes employing filler metal in all passes and shall be completely radiographed.

1.2.2 Class 2Pipe shall be double welded by processes employing filler metal in all passes. No radiography is required.

1.2.3 Class 3Pipe shall be single welded by processes employing filler metal in all passes and shall be completely radiographed.

1.2.4 Class 4Same as Class 3 except that the weld pass exposed to the inside pipe surface may be made without the addition of filler metal.

1.2.5 Class 5Pipe shall be double welded by processes employing filler metal in all passes and shall be spot radiographed.

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

TABLE 1 Recommended Heat Treatment

AlloyUNS DesignationPWHTA, B
Deg. F. (Deg. C)
Quench
200 (Ni)N022001650-1700 (900 to 928)Rapid Air/water
201 (Low C)N022011650-1700 (900 to 928)Rapid Air/water
400 (Ni-Cu)N044001650-1700 (900 to 928)Rapid Air/water
X (Ni-Cr-Mo-Fe)N060022150 (1177)CRapid Air/water
C22D (Low C-Ni-Mo-Cr)N060222050-(1120)CRapid Air/water
G30D (Ni-Cr-Fe-Mo-Cu)N060302150 (1177)CRapid Air/water
C2000D(Ni-Cr-Mo-Cu)N062002075-2125 (1135-1163)BRapid Air/water
230D (Ni-Cr-W-Mo)N062302150-2250 (1177-1232)BRapid Air/water
600 (Ni-Cr-Fe)N066001800-1850 (983 to 1010)Rapid Air/water
601 (Ni-Cr-Fe-Al)N066011600-1650 (874 to 900)ERapid Air/water
625 (Ni-Cr-Mo-Cb) Grade 1N066251600 (871)CRapid Air/water
625 (Ni-Cr-Mo-Cb) Grade 2N066252000 (1093)CRapid Air/water
G3D (Ni-Cr-Fe-Mo-Cu)N069852100-2150 (1147 to 1177)BRapid Air/water
Alloy 20 (Cr-Ni-Fe-Mo-Cu-Cb)N080201700-1850 (927 to 1010)Rapid Air/water
...N080241925-1975 (1052 to 1079)Rapid Air/water
...N080262050-2200 (1121 to 1204)Rapid Air/water
825 (Ni-Fe-Cr-Mo-Cu)N088251700-1800 (930 to 980)ERapid Air/water
C276 (Low C-Ni-Mo-Cr)N102762050 (1121)CRapid Air/water
B2 (Ni-Mo)N106651950 (1065)CRapid Air/water
B3D (Ni-Mo)N106751950 (1065)CRapid Air/water

A Recommended temperaturesDifferent temperatures may be selected by either the purchaser or the manufacturer.

B Set temperatures, ±25°F (±14°C).

C Minimum set temperature.

D Registered Trademark of Haynes International.

E Heat treatment is highly dependent on intended service temperature consult material manufacturer for specific heat treatments for end use temperature.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 02.04
Developed by Subcommittee: B02.07
Pages: 8
DOI: 10.1520/B0474-03R09
ICS Code: 77.150.40