Products and Services / Standards & Publications / Standards Products


    ASTM B361-02

    Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings

    SUPERSEDED (click for Active standard)

      Format Pages Price  
    PDF 5 $62.00   ADD TO CART

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center   Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Reprints and Permissions

    Permissions to reprint documents can be acquired through
    Copyright Clearance Center  

    Visit Copyright Clearance Center  

    Active (view current version of standard)

    Other Historical Standards

    ASTM License Agreement

    More B07.03 Standards Related Products

    1. Scope

    1.1 This specification covers only factory-made wrought aluminum and aluminum-alloy welding fittings in contrast to field-made fittings. The term "welding fittings" applies to butt-welding or socket-end parts, such as 45 elbows, 180 return bends, 90 short radius elbows, and other types made to the dimensional standards specified by ASME B16.9 and B16.11.

    Note 1—Throughout this specification use of the term alloyin the general sense includes aluminum as well as aluminum-alloy.

    1.2 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see .

    1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units which are provided for information only and are not considered standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and heal practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    B210 Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes

    B211 Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished Bar, Rod, and Wire

    B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

    B234 Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes for Condensers and Heat Exchangers

    B241/B241M Specification for Aluminum and Aluminum-Alloy Seamless Pipe and Seamless Extruded Tube

    B247 Specification for Aluminum and Aluminum-Alloy Die Forgings, Hand Forgings, and Rolled Ring Forgings

    B660 Practices for Packaging/Packing of Aluminum and Magnesium Products

    B881 Terminology Relating to Aluminum- and Magnesium-Alloy Products

    D3951 Practice for Commercial Packaging

    ASME Standards

    B16.11 Forged Fittings, Socket-Welding and Threaded

    Section IX Boiler and Pressure Vessel Code

    Section VIII Boiler and Pressure Vessel Code

    Federal Standards

    Fed. Std. No. 123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.

    ICS Code

    ICS Number Code 23.040.40 (Metal fittings)

    UNSPSC Code

    UNSPSC Code 11172000(Aluminum based alloys); 40183100(Tube fittings)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/B0361-02

    Citation Format

    ASTM B361-02, Standard Specification for Factory-Made Wrought Aluminum and Aluminum-Alloy Welding Fittings, ASTM International, West Conshohocken, PA, 2002, www.astm.org

    Back to Top